The so-performed alignment will be corrected to allow for the
tightening of pump flanges on pipes and depending on the tem-
peratures attained in service.
Note: it is recommended, after one week of operation, to check
the alignment again.
5.2 Hydraulic connections (see FIG.2)
-
The suction pipe
(
I)
w
ill have an ascending slope (2 % mini.)
without counter-slope, in order to prevent the formation of air
pockets and the risks of de-energizing. If the pipe diameter is
greater than that of the pump suction port, the connection
shall be performed through a cone with horizontal generatrix
(F). Comply with the proportions concerning the diameter
lengths and progressions for increasers and reducers
(F and G).
(
NFE 44201).
-
As the pump is not self-priming, it is mandatory, for a suction ope-
ration, that the pipe should be fitted with a strainer foot valve
(J).
- Perform a single rigid attachment
(H) close to pump, combined
with large-radius elbow (K), to compensate for thermal expan-
sion of the pipe.
- The pump must never be used as a support for pipes. Pipes must
be secured to the ground or wall (pipe support:
(H).
- Check that the connection of pipes to the pump leads to no
stresses able to cause a misalignment. In particular, bolts should
always penetrate freely in mounting holes, they will be tighte-
ned pr
ogressively and always in a diametrically opposed way.
- In installations where silence is wanted, provide on pump ports an
anti-vibration connection, for example using r
ubber slee
ves able
to bear the vacuum on suction and the pressure on discharge.
- Carefully clean the inside of pipes.
Annex connections (on N0 200-250D3 only)
Cooled bottom for liquid pumped at more than 105 °C (140 °C
maxi.), with circulation of cooling water
(see FIG.4).
- tapped connection ports : 1/4” dia.
- mean flowrates of cooling water : 200 l/h
- pressure in cooling circuit : 1 bar
- fluid : non-incrusting waters
5.3 Electrical connections
The electrical connections and checks must be made by
a licensed electrician and comply with applicable local
standards.
Motor protection mandatory by circuit-breaker with thermal and
magnetic protection.
- Check the voltage of available network.
- Read the instruction on cover of the motor terminal box
- Use a cable complying with EDF (French electricity board) stan-
dards (4 conductors + Earth) and connect to motor terminal
block (diagram inside the box, or see
FIG.5).
DO NOT FORGET TO CONNECT THE EARTH TERMINAL.
An error on electrical connection damages the motor. The
cable shall never touch the pipe or the pump.
6. STAR
TING UP
Before the first putting into service, perform mode-
ra
te greasing of lubricated rolling bearings.
For equipment with IP55 motor
s
,
put the plugs blanking the
condensates discharge ports back in place (the plugs are sup-
plied with the pump).
6.1 Filling - Venting
Ne
v
er opera
te the pump dr
y
,
e
v
en momentari
ly
.
- Fill the pump and suction pipe with the liquid to be conveyed.
After complete evacuation of the air, close the filling port.
- Make sure that no hard points subsist, by turning the pump by
hand through the coupling.
6.2 Check of the direction of rotation
- Power up the motor and check it turns in the direction indica-
ted by the arrow on pump body or on bearing (operation to be
p
erformed with the pump being uncoupled). In case of rever-
sal, cross two phase wires on the motor terminal block (or at the
c
ircuit-breaker).
6.3 Circuit-breaker
- Perform fine adjustment of the electrical protection, using an
ammeter connected to the motor under load.
- With motor stopped, cut a phase, power the motor back up
a
nd make sure the tripping is instantaneous.
- Check that the current consumption is lower than indicated on
the motor data plate.
6.4 Operation
Never operate the pump with no-flow condition
for more than 10 minutes.
- Check:
• for correct direction of rotation of the motor (pump uncoupled)
• that the mounting of pipes has not misaligned the motor-
pump shaft axes
• that the pump is full of liquid and that the air bleeding has well
been performed
• for tightness of gaskets of the suction duct to palliate any air
penetration.
- Put the motor-pump into service for a short instant and check
for regularity of return to stop.
- Starting the pump is performed with the discharge valve being
almost closed.
- Progressively open the valve up to the required operating pres-
sur
e (chec
k the maximum current).
- Pumps with low characteristics can then be started directly with
the discharge valve open in a position set to the operating
point.
Fabric packing
After a few hours operation, more significant leakage is necessa-
ry. This leakage must be reduced a few operating hours, by tigh-
tening the gland e
v
enly and without exaggerating in order to
prevent the shaft from overheating.
The gland must above all not heat. A well adjusted gland should
slightly and continually leak (10 to 20 drops per minute in operation).
Mechanical seal
A mechanical seal must never turn dry, even for
a shor
t instant.
Light leakage may occur during the run-in period. This leakage
will be attenuated after a few operating hours, possibly remai-
ning visible in the case of greasy fluids (oil).
Bleed the high points of the installation,
pump and mechanical seal.
7. MAINTENANCE
Chec
k that the pump tur
ns r
egular
ly and without vibr
ation.
Check the coupling catches.
Check for perfect greasing.
In an
y case,
chec
k the alignment of coupling shaft axes
.
On pumps with an IP55 motor
,
per
iodically remove the plugs from
the motors (on the front and rear bearings) to allow evacuation
of any condensates. In some cases, the fan cover must be remo-
ved.
8
ATTENTION !
ATTENTION !
ATTENTION !
ATTENTION !
ENGLISH
To Next Page
Loading...
