Salus VS20WRF Quick Guide

Scan for equipment
Name this equipment
Living room
Connect equipment
Finish
Digital programmable wireless 4 in 1 thermostat
Models: VS10WRF, VS10BRF,
VS20WRF, VS20BRF
Introduction
VS10..RF / VS20..RF is a room temperature thermostat that is used for wireless
control of iT600 series devices such as: KL08RF wiring centre, TRV radiator
valve and RX10RF boiler receiver. In combination with Universal Gateway
UGE600 this regulator can be controlled over the Internet using SALUS Smart
Home app (Online mode). Without Internet connection (Offline mode)
thermostat works locally, but its communication with other devices must be
done through the coordinating unit - CO10RF. Full version of the PDF manual
instruction is available on the website www.salus-controls.eu
Product compliance
EC Directives: 2014/30/EU, 2014/35/EU, 2014/53/EU i 2011/65/EU.
Full information is available on the website www.saluslegal.com
Power Supply: 4xAAA (alkaline batteries)
S1, S2 Terminals:
- external air or floor temperature sensor
- external contact (occupancy sensor)
- external hot water thermostat
(only with KL10RF configuration)
Montage: surface mounting (need to remove back cover)
Power Supply: 230V AC (L, N terminals)
1, 2 Terminals:
- external air or floor temperature sensor
- external contact (occupancy sensor)
- external hot water thermostat
(only with KL10RF configuration)
Montage: 60mm concealed box
L
S
230V AC
FUSE
T
N
Choose a ZigBee coordinator and prepare it to work with iT600 series
devices:
Firstly with the selected coordinator need to install devices, which
will be controlled by thermostat. Pairing method of each devices is
described in the manual instruction of a particular device.
KL08RF
RX10RF
• Online - connected to the Internet via the UGE600 gateway
or
• Offline -the ability to connect to the Internet using
the UGE600 gateway
or
• Offline - without Internet connection with CO10RF
coordinator
WARNING!
Do not use CO10RF coordinator
with UGE600 simultaneously.
Enter the wiring centre
number with or ,
Confirm your choice by .
Close the ZigBee network
Open the ZigBee network
Enter the zone number
with or ,
Confirm your choice by .
Wiring diagram - VS20WRF (white), VS20BRF (black)
Wiring diagram - VS10WRF (white), VS10BRF (black)
Installation - first start up
Installation - pairing with KL08RF / KL10RF wiring centre
Online Offline
OR
OR
LCD Icon description
Select the type of ZigBee coordinator:
Button Functions
Safety Information
Use in accordance to national and EU regulations. Use the device as
intended, keeping it in dry condition. Product for indoor use only.
Installation must be carried out by a qualified person in accordance to
national and EU regulations.
VII 2017
VS10WRF
T45 IP30
2 1 L
Probe
230VAC
N
-- --
MCU software*Numbers 88.8 and 8.8
relate to the software version
1. Comfort temperature
2. Standard temperature
3. Economic temperature
4. Automatic mode
5. PARTY mode
6. Holiday mode
7. Antifrost mode
8. Temperature unit
9. Group controller
10. Manual mode / override temp.
11. Current / set temperature
12. Program number
13. AM / PM
14. Lock function
15. Clock
Button
Function
Increasing/decreasing temperature or other value
Selecting the operating mode or switching between values
Short press - approve selection
Hold - enter / exit to or from the menu
Hold down these buttons to lock or unlock the keyboard
Hold down these buttons to enter installer mode
+
++
16. Day indicator
17. Settings
18. Low battery indicator
19. External temperature sensor
20. Hot water heating
21. Modes for Hot Water (KL10RF only)
22. Cooling mode ON
23. Internet connection indicator
24. Gateway wireless connection
25. Heating mode ON
ZigBee software
1
8
9
10
11
14
17 16 15
13
12
22
23
24
25
21
20
19
18
2 3 4 5 6 7
Thermostatic radiator
valve (TRV)
1
5
5
2
6
11
3
7
6
4
SALUS
Smart Home
Online Offline
5 sec
5 sec
5 sec
5 sec
Grouping
(Offline only)
Install the wiring centre
according to the instructions
attached to the product.
1
4
2 3
If the simplified configuration is not suitable, run the expanded configuration by
holding 3 keys as below until SEL PROG appears:
After approval of the type of thermostat, choose the type of device to
cooperation with:
Note: Thermostat is set by default as programmable (weekly).
Programmable (weekly)
Underfloor heating
- KL08RF or KL10RF wiring centre (underfloor heating)
Thermostat starts up in a simplified configuration mode. You can choose to pair with:
Daily
Thermostatic radiator
valve (radiator heating)
- Thermostatic radiator valve (radiator heating)
Hot Water timer (works only with KL10RF)
Set the theromstat type:
RX10RF in RX1 mode
RX10RF in RX2 mode
Installation - extended configuration
3
S1 S2
UP
S
T
for 14.4 MCU,
7.3 (VS20..RF), 10.9 (VS10..RF) ZigBee software version
Quick Guide

Salus VS20WRF Specifications

General

Brand	Salus
Model	VS20WRF
Category	Thermostat
Language	English