EasyManua.ls Logo

Samsung 650 - User Manual

Samsung 650
137 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
LCD TV
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please register
your product at
www.samsung.com/global/register
Model Serial No.

Table of Contents

Questions and Answers

  • P
    potternormanAug 20, 2025
    Why is Anynet+ not working on my Samsung TV?
    • J
      Joshua CastilloAug 20, 2025
      To troubleshoot Anynet+ issues on your Samsung TV, verify the following: * The connected device is an Anynet+ device, as the system supports only these devices. * Only one receiver (home theater) is connected. * The Anynet+ device's power cord is properly connected. * The Video/Audio/HDMI 1.3 cable connections of the Anynet+ device are secure. * Anynet+ (HDMI-CEC) is enabled in the Anynet+ setup menu. * The TV remote control is in TV mode. * You are using an Anynet+ exclusive remote control. * Be aware that Anynet+ may not function during channel searches or while operating WISELINK. * After connecting or disconnecting the HDMI 1.3 cable, search for devices again or power cycle your TV. * The Anynet+ function of the Anynet+ device is enabled.
  • B
    Briana HallAug 22, 2025
    What to do if the connected device is not displayed on Samsung 650 LCD TV?
    • J
      Joshua ReynoldsAug 22, 2025
      If a connected device isn't showing up on your Samsung LCD TV, consider these troubleshooting steps: * First, verify that the device actually supports Anynet+ functions. * Check that the HDMI 1.3 cable is securely connected. * Make sure Anynet+ (HDMI-CEC) is turned on within the Anynet+ setup menu. * Try rescanning for Anynet+ devices. Remember, only HDMI 1.3 cables support Anynet+ and some cables might not fully support it. * If the connection was interrupted (e.g., cable disconnection, power failure), repeat the device scan.
  • S
    Shane SuarezAug 25, 2025
    What to do if the message ‘Connecting to Anynet+ device...’ appears on the screen of Samsung LCD TV?
    • J
      James RobinsonAug 25, 2025
      If you see the message 'Connecting to Anynet+ device...' on your Samsung LCD TV, you won't be able to use the remote control during the configuration or view mode switching. Wait until the Anynet+ setting or switching to view mode is complete before using the remote.
  • S
    Sharon KleinAug 26, 2025
    Why is the connected device not displayed on my Samsung LCD TV?
    • K
      Kyle TaylorAug 26, 2025
      If a connected device isn't showing up on your Samsung LCD TV, first check if the device supports Anynet+ functions. Also, make sure the HDMI 1.3 cable is properly connected. Verify that Anynet+ (HDMI-CEC) is turned On in the Anynet+ setup menu. Try searching for Anynet+ devices again. Remember, you can only connect an Anynet+ device using an HDMI 1.3 cable, and some HDMI cables might not support Anynet+ functions. If the connection was interrupted due to a disconnected HDMI cable, power cord, or a power failure, repeat the device scan.
  • G
    Glenda TaylorAug 28, 2025
    How to start Anynet+ on Samsung TV?
    • K
      Kelli LynchAug 28, 2025
      To enable Anynet+ on your Samsung TV, ensure that the Anynet+ device is correctly connected to the TV. Then, check that Anynet+ (HDMI-CEC) is set to 'On' within the Anynet+ Setup menu. To access the Anynet+ menu, press the TV button on your TV remote to switch to TV mode, then press the TOOLS button and select the desired menu option.
  • W
    William LunaAug 30, 2025
    How to exit Anynet+ on Samsung TV?
    • T
      Tristan PerezAug 30, 2025
      To exit Anynet+ on your Samsung TV, you can either select 'View TV' from the Anynet+ menu, or press the SOURCE button on your TV remote and choose a device other than an Anynet+ device. Alternatively, press CH, CH LIST, PRE-CH, and FAV.CH to change the TV mode. Note that the channel button operates only when an Anynet+ device with a built-in tuner is not connected.
  • M
    michaelyoungSep 1, 2025
    What to do if the message 'Connecting to Anynet+ device...' appears on the Samsung TV screen?
    • K
      Karen WilliamsonSep 1, 2025
      If the message 'Connecting to Anynet+ device...' appears on your Samsung TV screen, it means you are currently unable to use the remote control. Please wait until the Anynet+ configuration or the switch to a view mode is complete before attempting to use the remote control.
  • J
    James LeeSep 3, 2025
    Why is the connected device not displayed on my Samsung TV?
    • C
      Carmen FloresSep 3, 2025
      If a connected device is not displayed on your Samsung TV, check the following: * Ensure that the device supports Anynet+ functions. * Verify that the HDMI 1.3 cable is properly connected. * Confirm that Anynet+ (HDMI-CEC) is set to 'On' in the Anynet+ setup menu. * Try searching for Anynet+ devices again. Note: Anynet+ devices should be connected using an HDMI 1.3 cable. Some HDMI cables may not fully support Anynet+ functions.
  • V
    valentineangelaSep 7, 2025
    How to start Anynet+ on Samsung 650 LCD TV?
    • L
      lindsay89Sep 7, 2025
      To start Anynet+ on your Samsung LCD TV, first ensure that the Anynet+ device is correctly connected to the TV. Then, check that Anynet+ (HDMI-CEC) is enabled in the Anynet+ Setup menu. Next, press the TV button on your remote to switch to TV mode. Finally, press the TOOLS button to bring up the Anynet+ menu and choose the desired option.
  • G
    Gregory FloresSep 9, 2025
    How to exit Anynet+ on a Samsung 650?
    • J
      Joshua MercerSep 9, 2025
      To exit Anynet+ on your Samsung LCD TV, you can try the following: * Select 'View TV' within the Anynet+ menu. * Alternatively, press the SOURCE button on your remote and select a source other than an Anynet+ device. * You can also attempt to change the TV mode by pressing z, CH LIST, PRE-CH, or FAV.CH. Note that the channel button only works if a tuner-embedded Anynet+ device is not connected.

Summary

Connection Panel Overview

Rear and Side Panel Jacks

Details the various input and output ports on the TV.

Remote Control

Remote Control Button Functions

Explains the purpose and operation of each button on the remote.

Cable TV Connection

Connecting Cable TV

Steps for connecting to a cable TV system, with or without a box.

Video Source Connections (HDMI;DVI)

Connecting via HDMI

Steps for connecting devices using an HDMI cable.

Connecting via DVI

Steps for connecting devices using a DVI to HDMI cable.

VCR Connections

Video and S-Video Connection

Steps for connecting a VCR using video and S-Video cables.

PC Connection

Connecting via D-Sub Cable

Steps for connecting a PC using a D-Sub cable.

Connecting via HDMI;DVI Cable

Steps for connecting a PC using an HDMI/DVI cable.

Basic TV Operation

Turning TV On;Off and Plug & Play Setup

How to power the TV on/off and complete initial setup.

Channel and Volume Management

Changing Channels

Methods for changing TV channels using different buttons.

Adjusting the Volume

How to adjust the TV volume using the remote control.

Display and Menu Navigation

Viewing Display Information, Menus, and Remote Backlight

Accessing display info, navigating menus, and using remote backlight.

Tools Menu and Channel Memorization

Using the TOOLS Button

Accessing frequently used functions quickly via the TOOLS menu.

Memorizing Channels and Selecting Signal Source

Steps for memorizing available channels and specifying the input source.

Storing Channels in Memory

Automatic Channel Storage

Guides on performing automatic channel memorization.

Source Selection and Editing

Selecting and Editing Input Source Names

Choosing input sources and personalizing their names.

Picture Control

Changing Picture Standard and Customizing Settings

Selecting picture modes and adjusting basic picture settings.

Detailed Picture Adjustments

Setting Black Adjust and Dynamic Contrast

Adjusting black level and optimizing screen contrast.

Advanced Picture Settings

Adjusting Gamma and Color Space

Adjusting primary colors and selecting color matrix for natural tones.

White Balance and Color Adjustments

Adjusting White Balance, Flesh Tone, and Edge Enhancement

Fine-tuning color temperature, flesh tone, and picture boundaries.

Picture Reset and xvYCC

Resetting Picture Settings to Factory Defaults and Setting xvYCC

Restoring picture settings to defaults and adjusting color space.

Configuring Picture Options

Activating and Setting Color Tone;Screen Size

Accessing and adjusting color tone and screen size options.

Screen Size Options

Screen Size Adjustments

Details on adjusting zoom, position, and scan settings for screen size.

Viewing Picture-in-Picture (PIP)

Activating and Configuring PIP

Steps to turn on and adjust PIP size and position.

Sound Control

Changing Sound Standard and Customizing Sound

Selecting sound modes and adjusting equalizer settings.

Channel Control

Managing Channels and Viewing All Channels

Adding, deleting, setting favorites, and viewing all available channels.

Channel List Management

Erasing and Adding Channels

Deleting or adding channels to customize the channel list.

Favorite Channels and Program Reservations

Setting Favorite Channels

Marking frequently watched channels as favorites.

Reserving a Program (Timer Viewing)

PC Display Setup

Using TV as PC Display and Display Modes

Setting up TV as PC monitor and understanding display modes.

PC Display Adjustments

Auto Adjust and Screen Quality Adjustment

Automatically adjusting PC signals and reducing picture noise.

Time Setting

Setting the Clock Manually

Automatic Clock Settings

Setting the Clock Automatically

Function Descriptions

Selecting Menu Language and V-Chip PIN Setup

V-Chip Parental Controls

Enabling;Disabling the V-Chip

Software Upgrade

Upgrading the Software

Instructions for updating the TV's firmware via USB.

WISELINK Functionality

Connecting USB Device and WISELINK Menu

Music List and Playback

Using the Music List

Network Connection (DHCP)

LAN Connection for DHCP Environment

Setting up network connection using DHCP for automatic IP allocation.

Automatic Network Setup

Automatic Network Configuration

Automatically configuring IP settings via DHCP.

Network Connection (Static IP)

LAN Connection for Static IP Environment

Steps for manually configuring network settings with a static IP.

Manual Network Setup

Manual IP Configuration

Manually entering IP address, subnet mask, gateway, and DNS.

InfoLink Service

Activating InfoLink

About Anynet+

Connecting Anynet+ Devices

Anynet+ Settings and Device Management

Setting Up Anynet+ Functions

Scanning and Switching Anynet+ Devices

Anynet+ Troubleshooting

Listening through Home Theater and Anynet+ Troubleshooting

General Troubleshooting

Troubleshooting Common TV Problems

Solutions for issues like poor picture, sound, or power.

Important Safety Instructions

General Safety Precautions

Essential safety guidelines for operating the TV.

Samsung 650 Specifications

General IconGeneral
Resolution1920 x 1080
Refresh Rate60 Hz
Smart TVYes
Display TypeLCD
Component Video Input1
Composite Video Input1
USB Ports2
Built-in Wi-FiYes

Related product manuals