How to fix Water Outlet thermistor SHORT or OPEN error on Samsung AE160ANYD H Heat Pump?
To address a SHORT or OPEN Water Outlet thermistor error on your Samsung Heat Pump, check its resistance. The expected resistance is 10kohm@25 °C for a Hydro unit, or 200kohm@25 °C for a DHW Tank or Solar unit.
What to do if the Water Inlet thermistor shows SHORT or OPEN on my Samsung AE160ANYD H?
If your Samsung Heat Pump displays a SHORT or OPEN error for the Water Inlet thermistor, check the thermistor's resistance. It should be 10kohm@25 °C for a Hydro unit, or 200kohm@25 °C for a DHW Tank or Solar unit.
How do I troubleshoot a SHORT or OPEN Water TANK thermistor error on my Samsung AE160ANYD H?
To troubleshoot a SHORT or OPEN Water TANK thermistor error on your Samsung Heat Pump, check the resistance of the thermistor. Look for a resistance of 10kohm@25 °C if you have a Hydro unit, or 200kohm@25 °C if it's a DHW Tank or Solar unit.
How to check Zone1 Water Outlet Thermistor if it shows SHORT or OPEN on Samsung AE160ANYD H?
If the Zone1 Water Outlet Thermistor displays a SHORT or OPEN error on your Samsung Heat Pump, check its resistance. The resistance should measure 10kohm@25 °C for a Hydro unit or 200kohm@25 °C for a DHW Tank or Solar unit.
What should I do if my Samsung AE160ANYD H Heat Pump shows Zone2 Water Outlet Thermistor SHORT or OPEN?
If your Samsung Heat Pump reports a SHORT or OPEN for the Zone2 Water Outlet Thermistor, you should check its resistance. It should be 10kohm@25 °C for a Hydro unit, or 200kohm@25 °C for a DHW Tank or Solar unit.
What to do if Wired remote controller thermistor shows SHORT or OPEN on Samsung AE160ANYD H Heat Pump?
If the wired remote controller thermistor displays a SHORT or OPEN error on your Samsung Heat Pump, you should check its resistance. It should measure 10kohm@25 °C for a Hydro unit or 200kohm@25 °C for a DHW Tank or Solar unit.
What does normal flow rate error mean on my Samsung Heat Pump?
This error indicates that the water pump is OFF but there's a normal flow rate. The system detects a normal flow rate when the water pump signal is OFF for 10 minutes.
How to fix short- or open-circuit error of room temperature sensor of Zone 1 indoor unit on Samsung AE160ANYD H Heat Pump?
To fix a short- or open-circuit error of the room temperature sensor of the Zone 1 indoor unit on your Samsung Heat Pump (detected only when the room thermostat is used), check the sensor's resistance. It should be 10kohm@25 °C for a Hydro unit or 200kohm@25 °C for a DHW Tank or Solar unit.
Essential safety guidelines and warnings for equipment installation and operation.
Details product compatibility and technical attributes of heat pump and indoor units.
Illustrates various system configurations for space heating and water heating.
Identifies and lists the key parts of the air to water heat pump system.
Provides a schematic representation of the system's operational flow and components.
Shows the physical dimensions and layout of the indoor unit for installation planning.
Instructions and requirements for safely mounting and positioning the indoor unit.
Guidelines and specifications for refrigerant and water pipe connections, including torque.
Comprehensive guide to electrical wiring, PCB layout, grounding, and power/communication cable connections.
Details for connecting thermostats, valves, boilers, and smart grid features for zone control.
Guide to accessing and using the self-test functions via the remote controller.
Explains error codes and possible causes for system malfunctions.
Information on installing and configuring the Domestic Hot Water (DHW) tank.
Details on installing, configuring, and operating the mixing valve for temperature control.
Procedures for installing temperature sensors on pipes for accurate readings.
Explanation of the special operating mode for concrete curing during floor heating installation.
Steps to adjust unit settings and options using the remote controller.
Instructions and tools required for safely extending the unit's power cable.
To Next Page
General