How to fix [Inverter] current sensor error in Samsung Heating System?
If your Samsung Heating System is showing an inverter current sensor error, check the EEPROM DATA and ensure the PCB is operating normally.
What to do if there is a tracking error between remote controller and the Hydro unit in my Samsung AE200RNWSEG Heat Pump?
If your Samsung Heat Pump displays a tracking error between the remote controller and the Hydro unit, the suggested solution is to change parts.
What does a low flow rate error mean on my Samsung AE200RNWSEG Heat Pump, and how do I fix it?
If your Samsung Heat Pump displays a low flow rate error, it indicates that there is not enough water flow. The suggested action is to turn the water pump ON.
What to do if my Samsung Heat Pump shows a short- or open-circuit error for the Zone 1 indoor unit room temperature sensor?
If your Samsung Heat Pump displays a short- or open-circuit error of the room temperature sensor of the Zone 1 indoor unit (detected only when the room thermostat is used), the suggested solution is to change parts.
How to fix [Inverter] DC LINK voltage sensor error in Samsung Heating System?
If your Samsung Heating System displays an inverter DC LINK voltage sensor error, check the input power connection and the status of RY21 and R200 in the INVERTER PCB.
How to troubleshoot thermostat wrong connection error on Samsung Heating System?
If your Samsung Heating System shows a thermostat wrong connection error, check the wiring of the Hydro Unit Thermostat and verify the cooling/heating signal for concurrent wiring issues.
How to troubleshoot compressor V limit error on Samsung Heating System?
If your Samsung Heating System displays a compressor V limit error, check the compressor connection status and the resistance between different phases of the compressor.
What should I check for indoor unit Eva In sensor (Open/Short) error in Samsung Heating System?
If your Samsung Heating System shows an indoor unit Eva In sensor (Open/Short) error, check the indoor unit Eva in sensor location.
How to fix indoor unit communication error on Samsung Heating System?
To address an indoor unit communication error in your Samsung Heating System: * Check the communication cable of the indoor unit. * Check the DC output voltage at the communication terminal.
How to fix [Inverter] compressor startup error in Samsung Heating System?
If you're experiencing a compressor startup error on your Samsung Heating System, check the compressor connection status. Also, check the resistance between different phases of the compressor.
Essential safety guidelines for service personnel during equipment repair.
Warnings about static discharge and PL effects on electronic components.
Critical safety measures to prevent electrical shock, fire, and injury.
Safety guidelines for managing refrigerants to protect health and environment.
Procedures and safety measures for brazing operations to prevent hazards.
Guidelines for safely charging refrigerants and testing operations.
Overview of the EHS system's key technologies and benefits, including energy saving.
Detailed technical specifications for outdoor and hydro units across various models.
List of accessories and optional items available for the EHS system.
List of essential hand tools required for product disassembly and reassembly procedures.
Step-by-step instructions for disassembling and reassembling the hydro unit.
Detailed procedures for safely disassembling and reassembling the outdoor unit components.
Guide to error codes displayed on the wired remote controller and their meanings.
Diagnostic procedures based on observed symptoms, including communication errors.
Specific troubleshooting steps for errors related to the hydro unit, such as EEPROM issues.
Pre-diagnostic checks including test run and view mode operations.
Further troubleshooting guidance for various system errors and symptoms.
Visual representation and component identification for the hydro unit's main PCB.
Diagrams and component labels for various PCBs used in the outdoor unit.
Electrical wiring schematics for different models of the tank integrated hydro unit.
Wiring diagrams illustrating connections for outdoor units across various phases and models.
Guide to interpreting model codes and their corresponding features and specifications.
System diagram and component list for the split tank integrated hydro unit.
System diagram and component list for the mono tank integrated hydro unit.
System schematic and part identification for the split Hydro Unit.
Instructions for checking and updating FSV data using S-NET Pro2 software.
Procedures for exporting and importing FSV values for EHS units via XML files.
Guidelines for loading and saving FSV values using an SD card with the EHS Converter.
General| Type | Air-to-Water Heat Pump |
|---|---|
| Refrigerant | R32 |
| Heating Capacity | 8.0 kW |
| Cooling Capacity | 7.0 kW |
| Energy Efficiency Class (Heating) | A++ |
| Energy Efficiency Class (Cooling) | A++ |
| Operating Temperature Range (Cooling) | -10°C to 46°C |
To Next Page
