Samsung MAX-6020 - Otherfunctions; Timer Function; For the Protection of Being Recorded

GB
17
The timer enables you to switch the system on or off at spe-
cific times.
Example: You wish to wake up to music every morning.
If you no longer want the system to be switched on or off auto-
matically, you must cancel the timer.
Before setting the timer, check that the current time is correct.
For each step, you have a few seconds to set the required
options. If you exceed this time, you must start again.
Switch the system on by pressing On/Standby.
Press Timer/Clock until TIMER is displayed.
Press Enter.
Result:
ON TIME is displayed (instead of the equalizer symbols) for
a few seconds, followed by any switch-on time already set;
you can set the timer switch-on time.
Set the timer switch-on time.
a Set the hour by pressing Tuning Mode Down and Up.
b Press Enter.
Result:
The minutes flash.
c Set the minutes by pressing Tuning Mode Down and Up.
d Press Enter.
Result:
OFF TIME is displayed (instead of the equalizer symbols)
for a few seconds, followed by any switch-off time already
set; you can now set the timer switch-off time.
Set the timer switch-off time.
a Set the hour by pressing Tuning Mode Down and Up.
b Press Enter.
Result: The minutes flash.
c Set the minutes by pressing Tuning Mode Down and Up.
d Press Enter.
Result:
VOL XX is displayed, where XX corresponds to the vol-
ume already set.
Press Tuning Down and Up to adjust the volume level and press
Enter.
Result:
The source to be selected is displayed.
Press Tuning Mode Down and Up to select the source to be played
when the system switches on.
If you select... You must also...
TAPE (cassette) Insert a recorded cassette in one of the
decks before setting the system to standby.
TUNER (radio) a Press
Enter.
b Select the FM or AM frequency band by
pressing Tuning Mode Down and Up.
c Press Enter.
d Select a preset station by
pressing
Tuning Mode Down and Up.
CD (compact disc) a Load one or more compact discs.
b Select the required disc.
Press Enter to confirm the timer.
Press On/Standby to set the system to standby mode.
Result
: is displayed to the bottom left of the time, indicating that
the timer has been set. The system will switch on and off
automatically at the required times.
If the timer switch on and off times are identical, the word ERROR is
displayed.
Press REC LOCK (recording protection) button.
When REC Lock (recording protection) lamp is lighted up all
of the buttons are not activated. (Volume, Demo button is
activated.)
It is a function that the recording stop is prevented by other
button action during recording.
REC Lock (recording protection) is activated only during
recording.
When the REC Lock is on (the lamp is on), do not open the
cassette door.
When releasing, press REC Lock button once again.
Timer Function
For the Protection of being Recorded
On/Standby
Demo
AI Off
/Sleep
TUNER C D TAPE AUX
+
–
Volume
Band
Mono/ST Memory Repeat Program Deck 1/2 REV mode
Normal
TAPE TAPE REC
HI-SpeedCD SYNC.REC/Pause
REC Lock
Shuffle
Tuning ModeDown Up
Timer
On/Off
Timer
/Clock
R
S
u
r
r
o
u
n
d
P
o
w
e
r
S
.
B
a
s
s
E
Q
M
u
t
e
E
n
t
e
r
TUNER C D TAPE
Band
Mono/ST Memory Repeat Program Deck 1/2 REV mode
Normal
TAPE TAPE REC
HI-SpeedCD SYNC.REC/Pause
es
REC Lock
Shuffle
Tuning ModeDown Up
7
8
9
5
6
1
2
3
4
1,9
2
3,4,5,6,7,8
4,5,6,7 4,5,6,7
MAX-6020/GB-15~22 5/20/03 16:53 Page 17