Samsung OfficeServ 7400 - Installation Guide Manual

Samsung OfficeServ 7400

82 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

OfficeServ 7400

Installation

Guide

Enterprise IP Solutions

Table of Contents

Introduction5
- Content and Organisation of the Guide5
- Conventions6
- Related Guides7
Default Chapter4
- Intended Use4
Safety Concerns8
- Warning9
- Caution10
- Table of Contents12
CHAPTER 1. Before Installing17
Site Information17
Grounding Conditions18
Power Conditions18
- Table 1.1 I/O Voltage of Power Supply Module18
Checking the Package19
- Table 1.2 Package Items19
CHAPTER 2. Installing Chassis20
Overview of System Installation Procedure20
- Figure 2.1 Chassis Front Panel20
Installing Chassis in a Rack21
- Precautions to Follow21
- Tools Required21
- Figure 2.2 Tools for Installation Inside a Rack21
- Installation22
- Figure 2.3 Rack Installation (1)22
- Figure 2.4 Rack Installation (2)22
- Figure 2.5 Rack Installation (3)23
- Figure 2.6 Rack Installation (4)23
Connecting the Grounding Wire24
- Figure 2.7 Grounding the Basic Chassis24
CHAPTER 3. Installing and Replacing Modules25
Chassis Configuration25
- Figure 3.1 Front Panels of Officeserv 7400 Chassis25
- Figure 3.2 Slot Numbers for Officeserv 7400 Chassis26
- Figure 3.3 Rear Panel of Officeserv 7400 Basic Chassis26
- Table 3.1 Mounting Modules in Slots26
Mounting Control Modules27
- Setting MP40 Module Switches and Mounting Optional Modules27
- Table 3.2 Components on the Rear Panel of Chassis27
- Figure 3.4 Setting Switches on MP40 Module28
- Table 3.3 Switches on MP40 Module28
- Setting LP40 Module Switches and Mounting Optional Modules29
- Figure 3.5 Mounting Optional Modem Module29
- Figure 3.6 Setting Switches on RCM2 Module29
- Figure 3.7 Mounting an Optional Module on the LP4030
- Table 3.4 Switches on RCM2 Module30
- Table 3.5 Position of Optional Modules30
- Mounting Control Modules31
- Table 3.6 Mounting Control Modules31
- Figure 3.9 Inserting the MP40 Control Module into the Connector on the Main Board32
- Figure 3.11 Inserting the LP40 Control Module into the Connector on the Main Board32
- Connecting an MP40 Module and an LP40 Module33
- Figure 3.12 Extension Cables33
- Connecting an MP40 Module to an Officeserv 7200 Expansion Chassis34
- Figure 3.13 Connecting the MP40 and LP40 Modules34
- Figure 3.14 Extension Cable34
- Figure 3.15 Connecting the MP40/LCP Module35
Mounting Interface Modules36
- Setting Switches and Mounting Optional Modules36
- Table 3.7 Interface Modules with Switches/Jumpers36
- Table 3.8 Interface Modules for Optional Modules36
- Figure 3.16 Setting GWIM Module Jumpers37
- Figure 3.17 Mounting a GWIMS Extension Module on the GWIM Module37
- Figure 3.18 Setting the MGI Module Switch38
- Figure 3.19 Mounting an MGI2D Optional Module on the MGI Module38
- Figure 3.20 Setting S1 Switch on the TEPRI Module39
- Figure 3.20 Setting Jumpers and Switches on the TEPRI Module39
- Figure 3.21 Setting Jumpers and Switches on the TEPRI2 Module40
- Figure 3.22 Setting the Jumpers on the PLIM Module41
- Figure 3.23 Setting the Jumpers on the GSIM Module42
- Figure 3.24 Setting the Jumpers on the GPLIM Module43
- Mounting Interface Modules in Slots44
- Table 3.9 Types of Interface Modules and Slots Available44
- Figure 3.25 Mounting an Interface Module in a Slot45
- Figure 3.26 Locking the Front Panel Lever of the Interface Module45
Connecting Power Backup Lines46
- Figure 3.27 Connecting Power Backup Line to a 16SLI Module46
Replacing Modules47
- Figure 3.28 Switching off the Chassis Power47
- Figure 3.29 Removing Cables to Control Module48
- Figure 3.30 Removing a Module48
- Figure 3.31 Mounting a Replacement Module49
CHAPTER 4. Connecting External Batteries and Rectifiers50
Connecting External Batteries50
- Figure 4.1 Connecting an External Battery51
Connecting an External Rectifier52
- Figure 4.2 Power Cable52
- Figure 4.3 Connecting an External Rectifier52
CHAPTER 5. Connecting Power Cables54
Caution When Connecting Power54
- Figure 5.1 Connecting the Power to a Basic Chassis55
- Figure 5.2 Connecting the Power to a Basic and Expansion Chassis55
CHAPTER 6 . Connecting C.O. Lines56
Line Conditions56
Connecting C.O. Lines56
- Table 6.1 Leak Resistance of Officeserv 7400 Lines56
CHAPTER 7. Connecting Stations and Additional Equipment58
Connecting Stations58
- Caution When Connecting Stations58
- Table 7.1 Maximum Distance between Stations and the System58
- Connecting Analogue Phones59
- Figure 7.2 RJ-45 Port of 16SLI Module59
- Figure 7.4 RJ-45 Port of 8COMBO Module (for Analogue Phone)59
- Connecting Digital Phones60
- Connecting IP Phones61
- Connecting a Wireless LAN Access Point64
Connecting Additional Equipment69
- Connecting MOH/BGM Equipment69
- Connecting External/Additional Paging Equipment70
- Connecting a Common Bell71
- Connecting Officeserv Webmmc71
- Connecting SMDR72
- Table 7.4 Specification of SMDR System72
- Connecting Printers73
Pre-Startup Check74
- System Environment74
- Safety Conditions74
CHAPTER 8. Starting the System74
CHAPTER 8. Starting the System75
Numbering Extensions and C.O. Lines76
Checking System Operation77
- Station Call Function77
- Station Camp-On Function77
- Line Call Function78
- Line Camp-On Function78
- Fan Operation79

Other manuals for Samsung OfficeServ 7400

Technical Manual159 pages

Installation Manual87 pages

Programming Guide20 pages

General Description112 pages

Related product manuals

Preview: Samsung OFFICESERV 7100

Samsung OFFICESERV 7100

Preview: Samsung OfficeServ 7200

Samsung OfficeServ 7200

Preview: Samsung OfficeServ 7100 Series

Samsung OfficeServ 7100 Series

Preview: OFFICESERV OfficeServ 7200

OFFICESERV OfficeServ 7200

Preview: Samsung OfficeServ

Samsung OfficeServ

Preview: Samsung OfficeServ 100

Samsung OfficeServ 100

Samsung OfficeServ 500

Preview: Samsung DCS

Preview: Samsung DCS-816

Samsung DCS-816

Preview: Samsung iDCS 500

Samsung iDCS 500

Preview: Samsung iDCS 100

Samsung iDCS 100

Preview: Samsung DCS KEYSET

Samsung DCS KEYSET