6WHS
: Install the Stand
Follow the steps below to connect the TV to the stand.
✎
NOTE
x
Make sure you distinguish between the front and back of the Stand and
Guide Stand when assembling them.
x
Make sure that at least two people lift and move the TV.
x
Stand the product up and fasten the screws. If you fasten the screws with
the PDP TV placed down, it may lean to one side.
Connect the Guide Stand to the
Stand using four screws (M4 X L12)
as shown.
With your TV upright, connect the
TV to the Stand as shown.
Fasten screws (M4 X L12) at
position , and then fasten the
two screws (M4 X L12) at position
.
s
s
s
s
Rear
Front
s
s
s
s
1
2
6WHS
: Install the Batteries into the Remote
To install batteries into your remote control,
follow these steps:
1. Lift the cover on the back of the remote
upward as shown in the figure to the
right.
2. Install two AAA batteries.
✎
Make sure to match the + and -
ends of the batteries to the diagram in the battery compartment.
3. Replace the cover.
6WHS
: Connect Power and Antenna or Cable
Quick Setup Guide
Congratulations on the purchase of your new Samsung TV.
Read this setup guide to get your TV up and running quickly.
1-800-SAMSUNG (1-800-726-7864)
Samsung Electronics America, Inc.
105 Challenger Road Ridgefield Park, NJ 07660-0511
Samsung Electronics Canada Inc.
55 Standish Court Mississauga, Ontario L5R 4B2
Call Center hours of operation: Mon-Sun, 9:00 AM -12
AM EST.
To register this product, visit: www.samsung.com/
register.
STOP
Please do not return this unit.
If you have problems operating your
TV, call:
1-800-SAMSUNG (1-800-726-7864)
For web support please visit:
www.samsung.com/support
6WHS
: Connect External Devices
Connecting an AV device (DVD/Blu-ray player, cable/satellite box, etc.)
6WHS
: Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language,
set the clock mode, and launch the TV’s channel memorizing process.
It also displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow
buttons on your remote. To make a selection, press the ENTER
button.
To skip a screen, press the MENU button. To turn on your TV, press the POWER
button on the r
emote or on the TV. To run Plug & Play, follow these steps:
Using your remote control,
select the language for the On
Screen Display (OSD), and then
press ENTER
=
button.
Select Home Use, and then
press ENTER
=
button. If you
select Store Demo, the TV will
reset your picture and audio
settings every 30 minutes.
Antenna Source is Air, Cable
or Auto, you must select
Antenna Source to same type
as your cable system type. After
selecting source, select Start;
then press the ENTER
button on your remote.
✎
Most cable systems are Standard(STD) systems, If you are not sure about
what kind of cable system you have, contact your cable company.
✎
If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After
Plug & Play is complete, set your TV to Channel 3 or 4, according to the
directions for your cable or satellite box.
The TV memorizes the available
channels. This process can take
up to 45 minutes.
After the TV has memorized
the channels, choose the
Clock Mode. Select Auto if
you have a digital channel in
your area. Select Manual if you
don’t, or if you have a cable or
satellite box. When done, press
ENTER
button.
✎
If you select Manual, the clock
setting screen appears.
Select the daylight savings time
setting: Off, On or Auto and
then press ENTER
=
button.
✎
This function is only available
when the Clock Mode is set to
Auto.
Select the time zone in which you live, and then press ENTER
button.
After the time zone screen, The connection method for best HD screen
quality is displayed. Press Right arrow button on your remote to view each
screen in succession. Press the Blue button to skip this section.
The Enjoy your TV. screen appears. Then press ENTER
=
button.
If You Want to Rerun Plug & Play
1. Press the SOURCE button on your remote, then select TV mode.
2. Pr
ess the MENU button on your remote to display the menu.
3. Press the or button to select Setup, and then press ENTER
=
button.
4. Press ENTER
again to select Plug & Play.
Connecting an audio device (Home Theater, etc.)
Connect your TV to your Home Theater or other audio device to enjoy enhanced
Sound quality.
Connecting a PC
Connect your TV to a PC to use it as a Monitor.
Top view
Rear
Front
Rear
Guide Stand
Screws (M4 X L12)
Stand
To Next Page
Loading...
