Samsung QM85N - User Manual

To Next Page

Quick Setup Guide

QM85N QM98N

* The colour and the appearance may differ depending on the product, and the content in

the manual is subject to change without prior notice to improve the performance.

* Download the user manual from the website for further details.

http://www.samsung.com/displaysolutions

BN68-09316F-01

1 Connects to MDC using a LAN cable. (10/100 Mbps)

2 Connect to a USB memory device.

* The USB ports on the product accept a maximum constant

current of 1.0A. If the maximum value is exceeded, USB ports

may not work.

3 DVI: Connects to a source device using a DVI cable or HDMI-DVI

cable.

MAGICINFO IN: To use MagicInfo, make sure to connect the DP-DVI

cable.

4 Connects to MDC using an RS232C adapter.

5 Connects to MDC using an RS232C adapter.

6 Receives sound from a source device via an audio cable.

7 Connects to a source device using a HDMI cable or HDMI-DVI cable.

8 Connects to a source device using a HDMI cable or HDMI-DVI cable.

Connects to another product using a HDMI cable.

9 Connects to a PC using a DP cable.

0 Connects to another product using a HDMI cable.

! Connect to a USB memory device.

* The USB ports on the product accept a maximum constant

current of 0.5A. If the maximum value is exceeded, USB ports

may not work.

@ Outputs sound to an audio device via an audio cable.

# Connects to an external IR cable that receives signals from the

remote control.

Checking the Components

Ports

Issues Solutions

The screen keeps

switching on and off.

Check that the cable between the product

and the PC is connected correctly.

No Signal is

displayed on the

screen.

Check that the product is connected

correctly with a cable.

Check that the source device connected to

the product is powered on.

Depending on the type of external device,

the screen may not display properly. In this

case, connect it with the HDMI Hot Plug

function turned On.

Not Optimum Mode

is displayed.

This message is displayed when a signal

from the graphics card exceeds the product’s

maximum resolution and frequency.

Refer to the Standard Signal Mode Table

and set the maximum resolution and

frequency according to the product

specifications.

The images on

the screen look

distorted.

Check the cable connection to the product.

The screen appears

unstable and shaky.

Check that the resolution and frequency of

the PC and graphics card are set within a

range compatible with the product. Then,

change the screen settings if required by

referring to ‘Preset Timing Modes’.

There are shadows or

ghost images left on

the screen.

Troubleshooting Guide

Contact the vendor where you purchased the product if any

components are missing.

The pictures may look different from the actual components.

Quick Setup Guide

Warranty card

(Not available in

some locations)

Power cord

Batteries (AAA x 2)

(Not available in

some locations)

Remote Control RS232C(IN) adapter

HOLDER-CABLE

Parts

The terms HDMI and HDMI High-Definition Multimedia Interface,

and the HDMI Logo are trademarks or registered trademarks of

HDMI Licensing LLC in the United States and other countries.

QM85N

QM98N

1 Power on the product.

If you press the

button when the product is turned on, the

control menu will be displayed.

2 Move to the upper or lower menu. You can also adjust the value

of an option.

3 Move to the left or right menu. You can also adjust the value of

an option.

4 Remote sensor

Press a button on the remote control pointing at the sensor on

the front of the product to perform the corresponding function.

Using other display devices in the same space as the remote

control of this product can cause the other display devices to be

inadvertently controlled.

1 Spacer logo

Do not pull on the spacer logo using force. The logo may tear or

break off.

2 Remote sensor

Press a button on the remote control pointing at the bottom of

the product face to perform the function. The remote control

sensor is located on the bottom of the product.

* Using other display devices in the same space as the remote

control of this product can cause the other display devices to

be inadvertently controlled.

3 Power button

2 31

Speaker

Network box

mounting hole

QM85N QM98N

Speaker

BN68-09316F-01_QSG_QMN 85-98_INDIA_ENG.indd 1 2019-07-01 오후 6:11:25

Need help?

Do you have a question about the Samsung QM85N and is the answer not in the manual?

Summary

Connecting and Using a Source Device

Connecting to a PC

Connects the display to a PC using HDMI, DVI, or DP cables for video output.

Connecting to MDC

Connects the display to MDC using LAN or RS232C cables for management.

Connecting to a Video Device

Connects the display to video sources like Blu-ray players or game consoles via HDMI.

Connecting to an Audio System

Connects the display to an audio system using the AUDIO OUT port.

Important Safety Instructions

General Safety Precautions

Provides essential safety warnings regarding installation, power, and environmental factors.

Electrical Safety

Advises on handling power cords, AC adapters, and preventing electric shock.