GB
27
GB
26
TV programme Download
★
(SV-657GX Only)
Direct Record Procedure
★
(SV-657GX Only)
Pictures and TV Picture Recording
★
(SV-657B Only)
TV Picture Record Setting
★
(SV-657GX Only)
Connecting an RCA Audio/Video Input Cable
★
(SV-657GX/SV-655GX/SV-651GX Only)
Using the Assemble Edit Function
Recording from Another VCR or Camcorder
Preparation:
◆ Turn on the TV.
◆ Select the video channel or the video input
mode on the TV.
1 Press the MENU on the remote control.
Result
: The programming menu is displayed.
2 Press the corresponding
"
,
❷
or
➛
,
❿
buttons to
select the INSTALLATION option.
And then press the OK button to select this option.
Result
: The
INSTALLATION menu is displayed.
3 Press the
"
or
❷
buttons to select
AV-LINK
SETTING
option. And then press the
❿!
button to
select this option.
Result
: The
AV-LINK menu is displayed.
4 Press the
"
or
❷
buttons, until the
TV CH
DOWNLOAD option is selected.
And then press the
❿
button to select this option.
5 Press the
❿
button to start TV CH DOWNLOAD
function.
6 When the downloading finished, then “TV CH
DOWNLOAD FINISHED
” is displayed.
7 Press the MENU button to exit.
➢
◆
The available position numbers on the
VCR are 1 to 80.
◆ When the TV’s channel position is
readjusted, the VCR automatically makes
“TV CH DOWNLOAD”.
1 Load a cassette with the safety tab attached.
2 Press the SPEED button to select the recording tape
speed.
3 Press two REC buttons to start recording.
Result
: The VCR automatically selects the same
picture as you are watching on the TV and
starts recording. Depending on the picture
sources, the recording switches the method.
See next page.
4 To stop a recording, press STOP (
■
) once.
➢ ◆ This recording is not available on the timer
programme recordings.
Preparation : turn on the TV.
1 Press the MENU on the remote control.
Result
: The programming menu is displayed.
2 Press the corresponding
"
,
❷
or
➛
,
❿
buttons to
select the
INSTALLATION option.
And then press the OK button to select this option.
Result: The
INSTALLATION menu is displayed.
3 Press the
"
or
❷
buttons to select
AV-LINK
SETTING
option. And then press the
❿!
button to
select this option.
Result
: The AV-LINK menu is displayed.
4 Press the
"
or
❷
buttons, until the
TV PICTURE
RECORD option is selected.
5
To... Press
➛
or
❿
until...
Record the same picture ON is displayed.
as you are watching on the TV
when you press REC button (
●
)
on the your VCR remote control.
Record the selected picture on OFF isdisplayed.
your VCR when you press REC
button (
●
) on your VCR
remote control.
6 Press the MENU button twice to exit.
➢ If this option is in ON mode, you press the
REC button (
●
) on the your TV remote
control, your VCR records the same picture
as you are watching on the TV.
You can connect other audio/video equipment to your
VCR using audio/video cables if the appropriate
outputs are available on the equipment chosen.
Examples
:
◆ You wish to copy a video cassette with the help
of a second VCR.
◆ You wish to play back and/or copy pictures
taken with a camcorder.
☛
◆ Make sure that both the television and the
VCR are switched off before connecting
the cables.
1 Connect one end of the RCA audio/video cable into
the VIDEO socket on the front of the VCR.
2 Plug the other end of the audio/video cable into the
appropriate output connector on the other system
(VCR or camcorder).
3 Connect one end of the RCA audio cable into the
AUDIO sockets on the front of the VCR.
➢ Take care to respect the colour coding of the
left and right channels.
4 Plug the other end of the audio cable into the
appropriate output connectors on the other system
(VCR, camcorder or Hi-Fi sound system).
You can copy a cassette to your VCR from another
video source, such as another VCR or a camcorder.
☛
It is an infringement of copyright laws to copy
prerecorded cassettes or to re-record them in
any form without the permission of the
owners of the corresponding copyright.
1 Connect the VCR, from which the cassette is to be
copied, to the appropriate SCART audio and video
input connectors on the rear of your VCR.
. You can also use an RCA audio and video cable to
connect the AUX input on the front of your VCR.
★
(SV-657GX/SV-655GX/SV-651GX only)
2 Insert a blank cassette in your VCR.
3 Insert the pre-recorded cassette in the other video
source (VCR or camcorder).
4 Press the INPUT button to select the appropriate
input on your VCR:
◆ AV1 or AV2 for the SCART input
◆ AUX for the RCA input
★
(SV-657GX/SV-655GX/
SV-651GX only)
Picture Channel selected on the TV. If you performed
“TV CH DOWNLOAD” (TV stations stored on
the VCR and the TV in the same position order).
If you did not perform “TV CH DOWNLOAD” (TV
stations not stored on the VCR and the TV in the
same position order).
Pictures of external equipment connected to the TV
Channel selected on the VCR
The VCR VCR channel of the same number as the TV
records: channel
AV1 (output of the TV)
AV1 (output of the TV)
VCR channel
During recording, if you change the channel or the input
mode on the TV, the recording will be:
Ex. TV channel 1
Continued.
Stopped.
Stopped.
Ex. VCR channel 1
Continued.
This function allows you to start a new recording at a
specific position on the cassette while maintaining a
very smooth scene change.
1 Insert the cassette to be edited in your VCR.
2 Press the
❿ll
button to start playback.
3 When you reach the position from which you wish to
start the new recording, press the
❿ll
button.
4 Press the F.ADV ( ) button again as often as
necessary to advance frame by frame, until the
exact recording position is located.
5 While the VCR is in still mode, hold the REC button
down for a while to activate the Assemble Edit
function.
Result: Record symbol flashes in the display.
6 Select the source from which you wish to record by
pressing:
◆ The PROG/TRK (
"
or
❷
) / PROG (
"
or
❷
)
buttons for television channels
◆ The INPUT button for the AV1, AV2 or AUX
★
(SV-657GX/SV-655GX/SV-651GX only) input
sources
7 Press the
❿ll
button to start recording.
8 When you have finished recording, press
■
.
To Next Page
Loading...
Need help?
General
