EasyManua.ls Logo

Samsung WD8 K64 Series - WASHING MACHINE TROUBLESHOOTING; COMMON TROUBLESHOOTING CHECK MODES

Samsung WD8 K64 Series
54 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Troubleshooting _ 35
4. TROUBLESHOOTING
4-1. CHECK MODES
► This is a washer integrated check mode. For detailed information, refer to the general repair scripts.
Check Type
Check
Mode
Causes Remarks
Water Level
Sensor
1C
- Thepartofthehosewherethewaterlevelsensorislocatedis
damaged(punctured).
- Thehoseiscloggedwithforeignmaterial.
- Thehoseisfolded.
- Toomuchlubricanthasbeenappliedtotheinsertionpartofthe
airhose.
- Hoseengagementcheck.(disengaged)
- Partfault.(Faultyinternalsoldering)
- Thewaterlevelsensorterminalisdisengaged.
- MainPBAfault.
Motor Driving
Check and Hall
Sensor Check
3C
- ThePBAconnectorterminalisnotconnected.
- Themotorspinnetisnotengaged.
- Themotor’sinternalcoilisdamaged.(short-circuitedorcut)
- Thehallsensorterminalisnotconnected.
- Foreignmaterial(ascrew)hasenteredthemotor.
- Motoroverloadedduetotoomuchlaundry.(Non-sensing)
- Themotorhallsensorterminalisnotconnected.
- PBAfault.
- ThemotordrivingcheckfromthePBAisweak.
Unstablerelayoperation,etc.
- Thisoccursduetoerroneousoperatingsignalsfromthemotor
hallsensor.
- TheIPMterminalofthemainPBAisnotconnected.
- TheDDmotorcoverisoutofplace.
- ThePCBhousingterminalisnotconnected.
- PBAfault.
- DDmotorfault.
Thischeckoccurs
becauseofrestrained
revolutions.
Thischeckoccurs
whenaninterference
isgeneratedduetotoo
muchlaundry,etc.
Water Supply
Check
4C
- Foreignmaterialisenteringthewatersupplyvalve.
- Thewatersupplyvalveterminalisnotconnected.
(Wiredisconnected)
- Thewarmwaterandrinseconnectorsarewronglyconnected
toeachother.
- ThisoccursifthePCBterminalfromthedrainhosetothe
detergentdrawerisnotconnected.Checkwhetherthe
transparenthoseisfoldedortorn.
4C2
- Thecoldandwarmwatersupplyhosesarewronglyengaged
intoeachother.
- Thetemperatureofthewatersuppliedthroughthedryvalve
duringadrycycleissensedashigherthan70˚C.
- Thewatertemperatureissensedashigherthan50˚Cinthe
WoolorLingeriecourses.
Thewatersuppliedfor
1minutedryingthe
dryingcycleis0.3~
0.4L.
Drain Check 5C
- Thepumpmotorimpellerisdamagedinternally.
- Thewrongvoltageissuppliedtotheparts.
- Partfault.
- Thisoccursduetofreezinginthewinterseason.
- Thedrainhoseisclogged.(Injectioncheck,foreignmaterial)
- Cloggedwithforeignmaterial.
- Thewaterpumpterminalisnotconnected:rubberband,bills,
cotton,hairpins,coinshavecollectedinsidethedrainpump
ASSY.
WD6500K_7-8-9-11kg_1400rpm-SM.indb 35 2018/11/9 9:53:31

Related product manuals