What causes communication errors in a Samsung WW1 T Washer?
Communication errors in your Samsung Washer can occur if the signals between the sub and main PBAs are not sensed. Check the connector connections between the sub and main PBAs carefully and look for any faulty soldering after removing the sub PBA C/Panel. These issues may indicate a Main PCB and Sub PCB Signal Detection fault or a Main PCB and Sub PCB wire connection fault.
Why Samsung WW1 T Washer does not start?
Your Samsung Washer might not start due to several reasons. First, ensure the washing machine is properly plugged in. Check that the door is completely closed and that the water taps are open. Tap and hold to start the washing machine. Also, verify that Child Lock is not activated. Before the washing machine starts filling, it will make clicking noises to check the door lock and perform a quick drain. Check the fuse or reset the circuit breaker, and ensure power is supplied correctly. If a low voltage is detected, make sure the power cord is plugged in. Ensure no laundry is caught in the door. If the AddWash door is open, close it properly and tap and hold to try again. To add laundry, close the AddWash door completely and tap and hold to resume operation.
What to do if Samsung Washer does not drain and/or spin?
If your Samsung washer isn't draining or spinning, ensure the drain hose is straight and the debris filter isn't clogged. Close the door and tap and hold the start button. Make sure the drain hose isn't frozen or connected to a clogged drain system. Insufficient power can also cause this issue; the washer should resume normal operation once power is restored. Also, verify the drain hose is correctly positioned.
What to do if Samsung WW1 T leaks water?
If your Samsung washer is leaking water, ensure the door is properly closed and all hose connections are tight. Make sure the drain hose is correctly inserted and secured to the drain system, and avoid overloading the machine. Using high efficiency (HE) detergent can also help prevent oversudsing, which can cause leaks. Check the drain hose to ensure it is not placed on the floor or clogged.
What to do if Samsung WW1 T Washer door does not open?
If the door of your Samsung washer won't open, tap and hold the start button to stop the machine. It may take a few moments for the door lock to disengage. The door will not open until 3 minutes after the washer has stopped or the power has been off. Ensure all water in the drum is drained and that the door lock light is off.
Why Samsung WW1 T cannot add additional detergent?
If you cannot add additional detergent to your Samsung washer, make sure the remaining amount of detergent and fabric softener is not over the limit.
Why Samsung Washer fills with the wrong water temperature?
If your Samsung washer is filling with the wrong water temperature, fully open both taps and ensure the temperature selection is correct. Verify the hoses are connected to the correct taps and flush the water lines. The water heater should supply a minimum of 49 °C hot water. Also, disconnect the hoses and clean the mesh filter. Note that the water temperature may change during filling as the automatic temperature control feature checks the incoming water temperature.
Why Samsung WW1 T has odours?
Odors in your Samsung washer can be due to excessive suds collecting in recesses. Run cleansing cycles periodically to sanitize the machine. Also, clean the door seal (diaphragm) and dry the washing machine interior after each cycle.
Why Samsung WW1 T excessive vibrations or makes noise?
Excessive vibration or noise in your Samsung washing machine can occur if the washer isn't on a level, solid floor; use the leveling feet to adjust. Ensure the shipping bolts have been removed and the washer isn't touching anything else. Check that the laundry load is balanced. The motor can cause noise during normal operation. Metal objects such as coins can cause noise; remove them from the drum or filter case after washing.
What to do if Samsung WW1 T Washer has insufficient water supply?
If your Samsung washer isn't getting enough water, make sure the water tap is fully open. Ensure the door is properly closed. Also, check that the water supply hose isn't frozen, kinked, or clogged. Verify that there's sufficient water pressure. Confirm that the cold and hot water taps are correctly connected. Finally, clean the mesh filter, as it might be clogged.
Explains the importance of safety instructions and manual usage.
Defines symbols used in the manual for warnings and cautions.
Lists essential precautions to reduce risk of fire, shock, or injury.
Highlights warnings related to the installation process.
Warns about potential hazards during appliance operation.
Outlines necessary conditions for electrical supply, grounding, and water.
Instructions for adjusting levelling feet for stability and proper operation.
Detailed steps for connecting the water hose to the tap and machine.
Guide for connecting the water hose to non-threaded taps using an adapter.
Guides through first-time setup, language selection, and machine calibration.
Details the functions of each button and display element on the control panel.
Step-by-step guide on how to select and operate a wash cycle.
Common problems and their basic troubleshooting steps.
Explains error codes displayed on the screen and their solutions.
General| Digital Inverter Motor | Yes |
|---|---|
| Eco Bubble Technology | Yes |
| Quick Wash | Yes |
| Delay Start | Yes |
| Child Lock | Yes |
| Capacity | 9 kg |
| Spin Speed | 1400 rpm |
| Color | White |
| Energy Rating | A+++ |
| Dimensions (HxWxD) | 850 x 600 x 550 mm |
To Next Page
