Why does my Samsung WW10T654DLE show an unbalance error?
The unbalance error on your Samsung Washer is caused by the laundry load. Check the laundry to resolve this issue, as this occurs by laundry.
Why is there no water supply in my Samsung WW10T654DLE Washer?
If your Samsung Washer isn't getting water, it could be due to several reasons. Foreign material may be entering the water supply valve, or the water supply valve terminal might not be connected properly. The warm water and rinse connectors could be wrongly connected. Also, check if the PCB terminal from the drain hose to the detergent drawer is not connected, or if the transparent hose is folded or torn. Low water pressure, or a frozen water valve in winter, can also cause this issue. In this case, the water supply valve may be faulty.
Why does my Samsung Washer overflow?
Your Samsung Washer may be overflowing due to a few potential issues. It could be that water is supplied continually because the water level detection isn't working, possibly due to a clogged drain hose or an injection error. Freezing or foreign material in the water supply valve can also cause continuous water supply. A faulty sensor, or a blocked or damaged pressure tube might also be responsible. All these scenarios can be related to a water level sensor fault.
Why is the water level wrong in my Samsung WW10T654DLE Washer?
If the water level in your Samsung Washer is incorrect, it could be due to several reasons. The hose where the water level sensor is located might be damaged, clogged with foreign material, or folded. Too much lubricant on the air hose insertion part, a hose engagement error, a part fault (like faulty internal soldering), a disengaged water level sensor terminal, or a main PBA fault can also cause this. These issues point to a water level sensor fault.
Why is my Samsung WW10T654DLE heater not working?
If the heater in your Samsung Washer isn't working, it could be due to a short-circuited washing heater or a disconnected wire. There might be a contact error or temperature sensor fault in the washing heater inside the tub. Also, if the water level sensor operates without water (due to frozen water or another reason) and the temperature sensor detects a high temperature (100 to 150 ?C), the washing machine will turn off the input power. This suggests a heater fault.
What causes communication errors in a Samsung WW10T654DLE?
Communication errors in your Samsung Washer can occur if the signals between the sub and main PBAs are not sensed. Check the connector connections between the sub and main PBAs carefully and look for any faulty soldering after removing the sub PBA C/Panel. These issues may indicate a Main PCB and Sub PCB Signal Detection fault or a Main PCB and Sub PCB wire connection fault.
Instructions for safe operation and servicing, including warnings and cautions.
Details on washing machine capacity, power consumption, dimensions, and spin revolutions for various models.
Comparison table of features, specifications, and design elements across different washing machine models.
Lists optional parts, their part codes, descriptions, and quantities for washing machines.
Lists and describes the tools required for disassembling and reassembling washing machine components.
Illustrates the step-by-step process for disassembling and reassembling various parts of the washing machine.
Details information codes displayed by the washing machine, their causes, and corrective actions.
Provides a checklist of common washing machine problems and their corresponding solutions.
Schematic diagram illustrating the simple wiring connections within the washing machine.
Schematic diagram showing the wiring connections for the LED display model of the washing machine.
Schematic diagram detailing the wiring connections for the Q-Drive washing machine models.
Explains the model naming convention and project structure for WW6000T washing machines.
Defines key terms and components used within the washing machine service manual.
General| Model | WW10T654DLE |
|---|---|
| Capacity | 10 kg |
| Washing Capacity (kg) | 10 kg |
| Energy Efficiency Class | A |
| Spin Speed | 1400 RPM |
| Color | White |
| Wi-Fi Connectivity | Yes |
| Noise Level (Spinning) | 72 dB |
| Digital Inverter Technology | Yes |
| AI Wash | Yes |
| AddWash | Yes |
| Hygiene Steam | Yes |
| Drum Clean | Yes |
| SmartThings App Support | Yes |
| Digital Inverter Motor | Yes |
| Eco Bubble Technology | Yes |
| Quick Wash | Yes |
| Delay Start | Yes |
| Child Lock | Yes |
| Type | Front Load |
| Dimensions (H x W x D) | 850 x 600 x 600 mm |
| Water Consumption | 45 L |
To Next Page