To Next Page
B
barbaragreenAug 7, 2025
Why does my Samsung Washer show an unbalance error?
- PPaul ScottAug 8, 2025
The unbalance error on your Samsung Washer is caused by the laundry load. Check the laundry to resolve this issue, as this occurs by laundry.
Why does my Samsung Washer show an unbalance error?
The unbalance error on your Samsung Washer is caused by the laundry load. Check the laundry to resolve this issue, as this occurs by laundry.
Why is there no water supply in my Samsung WW10TP34DSG Washer?
If your Samsung Washer isn't getting water, it could be due to several reasons. Foreign material may be entering the water supply valve, or the water supply valve terminal might not be connected properly. The warm water and rinse connectors could be wrongly connected. Also, check if the PCB terminal from the drain hose to the detergent drawer is not connected, or if the transparent hose is folded or torn. Low water pressure, or a frozen water valve in winter, can also cause this issue. In this case, the water supply valve may be faulty.
Why does my Samsung WW10TP34DSG Washer overflow?
Your Samsung Washer may be overflowing due to a few potential issues. It could be that water is supplied continually because the water level detection isn't working, possibly due to a clogged drain hose or an injection error. Freezing or foreign material in the water supply valve can also cause continuous water supply. A faulty sensor, or a blocked or damaged pressure tube might also be responsible. All these scenarios can be related to a water level sensor fault.
Why is the water level wrong in my Samsung WW10TP34DSG Washer?
If the water level in your Samsung Washer is incorrect, it could be due to several reasons. The hose where the water level sensor is located might be damaged, clogged with foreign material, or folded. Too much lubricant on the air hose insertion part, a hose engagement error, a part fault (like faulty internal soldering), a disengaged water level sensor terminal, or a main PBA fault can also cause this. These issues point to a water level sensor fault.
Why is my Samsung WW10TP34DSG heater not working?
If the heater in your Samsung Washer isn't working, it could be due to a short-circuited washing heater or a disconnected wire. There might be a contact error or temperature sensor fault in the washing heater inside the tub. Also, if the water level sensor operates without water (due to frozen water or another reason) and the temperature sensor detects a high temperature (100 to 150 ?C), the washing machine will turn off the input power. This suggests a heater fault.
What causes communication errors in a Samsung Washer?
Communication errors in your Samsung Washer can occur if the signals between the sub and main PBAs are not sensed. Check the connector connections between the sub and main PBAs carefully and look for any faulty soldering after removing the sub PBA C/Panel. These issues may indicate a Main PCB and Sub PCB Signal Detection fault or a Main PCB and Sub PCB wire connection fault.
General safety guidelines for operating and servicing the washing machine.
Detailed technical specifications for various washing machine models.
Comparison of features and specifications across different washing machine models.
Lists optional parts and accessories for the washing machines.
Lists the necessary tools required for disassembling and reassembling the washing machine.
Provides standard diagrams and steps for disassembling various machine components.
Lists error codes, their causes, and corrective actions for washing machine malfunctions.
Provides a checklist of common washing machine problems and their solutions.
Schematic diagram illustrating the basic wiring connections of the washing machine.
Wiring diagram specifically for washing machine models with LED displays.
Wiring diagram for washing machine models equipped with the Q-Drive feature.
Explains the model naming convention and project structure for WW6000T series.
Defines key terms and components used in the washing machine service manual.
General| Model | WW10TP34DSG |
|---|---|
| Type | Front Load Washer |
| Capacity | 10 kg |
| Energy Rating | A+++ |
| Spin Speed | 1400 RPM |
| Dimensions (H x W x D) | 850 x 600 x 550 mm |
| Color | White |
| Body color | White |
| Panel Display | LED |
| Net Dimension (WxHxD) | 600 x 850 x 550 mm |
| Inverter Motor | Yes |
| Digital Inverter Technology | Yes |
| Eco Bubble Technology | Yes |
| Quick Wash | Yes |
| Delay Start | Yes |
| Child Lock | Yes |
