Why Samsung WW90TA046TE won't start?
If your Samsung Washer isn't starting, there could be several reasons. Ensure it's properly plugged in and the door is completely closed. Check that the water taps are open and you've pressed the Start/Pause button. Also, verify that Child Lock is not activated. It's normal for the washer to make clicking noises and do a quick drain before filling. Finally, check the fuse or reset the circuit breaker.
What to do if my Samsung WW90TA046TE Washer vibrates excessively or makes noise?
Excessive vibration or noise in your Samsung Washer can stem from several factors. Ensure the washer is on a level, solid, non-slippery floor, adjusting the leveling feet if needed. Check that the shipping bolts have been removed and that the washer isn't touching anything else. Make sure the laundry load is balanced. Note that the motor's operation and metal-decorated clothes can cause noise. Remove any metal objects like coins from the drum or filter case.
Why does my Samsung WW90TA046TE show an unbalance error?
The unbalance error on your Samsung Washer is caused by the laundry load. Check the laundry to resolve this issue, as this occurs by laundry.
What to do if water supply is insufficient in Samsung WW90TA046TE?
If your Samsung Washer isn't getting enough water, make sure the water tap is fully open and the door is properly closed. Check that the water supply hose isn't frozen, kinked, or clogged. Also, ensure there's sufficient water pressure.
How to prevent detergent from remaining in the drawer of my Samsung WW90TA046TE Washer?
To prevent detergent from remaining in the detergent drawer of your Samsung Washer, ensure the washing machine is running with sufficient water pressure. Add detergent to the center of the drawer and make sure the rinse cap is properly inserted. If using granular detergent, position the detergent selector to the upper setting. You may also need to remove the rinse cap and clean the detergent drawer.
Why is there no water supply in my Samsung WW90TA046TE Washer?
If your Samsung Washer isn't getting water, it could be due to several reasons. Foreign material may be entering the water supply valve, or the water supply valve terminal might not be connected properly. The warm water and rinse connectors could be wrongly connected. Also, check if the PCB terminal from the drain hose to the detergent drawer is not connected, or if the transparent hose is folded or torn. Low water pressure, or a frozen water valve in winter, can also cause this issue. In this case, the water supply valve may be faulty.
Why does my Samsung WW90TA046TE Washer overflow?
Your Samsung Washer may be overflowing due to a few potential issues. It could be that water is supplied continually because the water level detection isn't working, possibly due to a clogged drain hose or an injection error. Freezing or foreign material in the water supply valve can also cause continuous water supply. A faulty sensor, or a blocked or damaged pressure tube might also be responsible. All these scenarios can be related to a water level sensor fault.
Why is the water level wrong in my Samsung Washer?
If the water level in your Samsung Washer is incorrect, it could be due to several reasons. The hose where the water level sensor is located might be damaged, clogged with foreign material, or folded. Too much lubricant on the air hose insertion part, a hose engagement error, a part fault (like faulty internal soldering), a disengaged water level sensor terminal, or a main PBA fault can also cause this. These issues point to a water level sensor fault.
Why is my Samsung WW90TA046TE Washer heater not working?
If the heater in your Samsung Washer isn't working, it could be due to a short-circuited washing heater or a disconnected wire. There might be a contact error or temperature sensor fault in the washing heater inside the tub. Also, if the water level sensor operates without water (due to frozen water or another reason) and the temperature sensor detects a high temperature (100 to 150 ?C), the washing machine will turn off the input power. This suggests a heater fault.
What causes communication errors in a Samsung Washer?
Communication errors in your Samsung Washer can occur if the signals between the sub and main PBAs are not sensed. Check the connector connections between the sub and main PBAs carefully and look for any faulty soldering after removing the sub PBA C/Panel. These issues may indicate a Main PCB and Sub PCB Signal Detection fault or a Main PCB and Sub PCB wire connection fault.
Covers critical installation, usage, and cleaning warnings to prevent injury and hazards.
Detailed steps for removing shipping bolts, adjusting feet, and connecting hoses.
Instructions for connecting the water supply and drain hoses to the appliance.
Explains the control panel, cycle selection, display, and key buttons like Temp., Rinse, Spin.
Details standard cycles, their descriptions, load capacities, and specific features.
General| Control type | Rotary |
|---|---|
| Display type | LED |
| Loading type | Front-load |
| Product color | White |
| Built-in display | Yes |
| Custom panel-ready | - |
| Appliance placement | Pedestal |
| Drum capacity | 9 kg |
| Cycle time (max) | 228 min |
| AquaStop function | No |
| Spin-drying class | B |
| Maximum spin speed | 1400 RPM |
| Noise level (spin) | 72 dB |
| Energy efficiency scale | A to G |
| Water consumption per cycle | 50 L |
| Energy consumption washing per cycle | - kWh |
| Package depth | 660 mm |
| Package width | 670 mm |
| Package height | 890 mm |
| Package weight | 67000 g |
Weight and Dimensions| Depth | 550 mm |
|---|---|
| Width | 600 mm |
| Height | 850 mm |
| Weight | 65000 g |
To Next Page
