To Next Page
A
Andrew MasonAug 7, 2025
Why does my Samsung WW90TA046TT show an unbalance error?
- JJon GarciaAug 8, 2025
The unbalance error on your Samsung Washer is caused by the laundry load. Check the laundry to resolve this issue, as this occurs by laundry.
Why does my Samsung WW90TA046TT show an unbalance error?
The unbalance error on your Samsung Washer is caused by the laundry load. Check the laundry to resolve this issue, as this occurs by laundry.
Why is there no water supply in my Samsung WW90TA046TT?
If your Samsung Washer isn't getting water, it could be due to several reasons. Foreign material may be entering the water supply valve, or the water supply valve terminal might not be connected properly. The warm water and rinse connectors could be wrongly connected. Also, check if the PCB terminal from the drain hose to the detergent drawer is not connected, or if the transparent hose is folded or torn. Low water pressure, or a frozen water valve in winter, can also cause this issue. In this case, the water supply valve may be faulty.
Why does my Samsung WW90TA046TT Washer overflow?
Your Samsung Washer may be overflowing due to a few potential issues. It could be that water is supplied continually because the water level detection isn't working, possibly due to a clogged drain hose or an injection error. Freezing or foreign material in the water supply valve can also cause continuous water supply. A faulty sensor, or a blocked or damaged pressure tube might also be responsible. All these scenarios can be related to a water level sensor fault.
Why is the water level wrong in my Samsung WW90TA046TT?
If the water level in your Samsung Washer is incorrect, it could be due to several reasons. The hose where the water level sensor is located might be damaged, clogged with foreign material, or folded. Too much lubricant on the air hose insertion part, a hose engagement error, a part fault (like faulty internal soldering), a disengaged water level sensor terminal, or a main PBA fault can also cause this. These issues point to a water level sensor fault.
Why is my Samsung Washer heater not working?
If the heater in your Samsung Washer isn't working, it could be due to a short-circuited washing heater or a disconnected wire. There might be a contact error or temperature sensor fault in the washing heater inside the tub. Also, if the water level sensor operates without water (due to frozen water or another reason) and the temperature sensor detects a high temperature (100 to 150 ?C), the washing machine will turn off the input power. This suggests a heater fault.
What causes communication errors in a Samsung WW90TA046TT Washer?
Communication errors in your Samsung Washer can occur if the signals between the sub and main PBAs are not sensed. Check the connector connections between the sub and main PBAs carefully and look for any faulty soldering after removing the sub PBA C/Panel. These issues may indicate a Main PCB and Sub PCB Signal Detection fault or a Main PCB and Sub PCB wire connection fault.
Instructions for safe operation and accident prevention during servicing.
Details on model name, dimensions, capacity, power consumption, and spin revolutions.
Comparison of key specifications across different washing machine models.
Lists optional parts, their part codes, figures, descriptions, and quantities.
Details on tools required for disassembly and reassembly, with remarks on their usage.
Illustrates standard procedures for disassembling and reassembling various parts of the washing machine.
Lists error codes, their causes, and corrective actions for abnormal washing machine conditions.
Provides solutions for common washing machine problems like not starting, vibration, or drainage issues.
Presents a basic schematic diagram of the washing machine's internal wiring connections.
Provides the schematic diagram for washing machine models equipped with LED displays.
Details the wiring diagram specifically for washing machine models featuring the Q-DRIVE technology.
Explains the model naming convention and project structure for WW6000T series washing machines.
Defines key terms used in the service manual, such as Drain Pump, Heater, and Door Lock Switch.
General| Door hinge | Left |
|---|---|
| Water fill | Cold |
| Control type | Rotary, Touch |
| Display type | LED |
| Loading type | Front-load |
| Tub material | Plastic |
| Drum material | Stainless steel |
| Product color | White |
| Built-in display | Yes |
| Custom panel-ready | - |
| Illumination color | Blue |
| Appliance placement | Freestanding |
| Lower built-in capability (topless) | No |
| Drum capacity | 9 kg |
| Cycle time (max) | 314 min |
| Residual moisture | 44 % |
| Spin-drying class | B |
| Maximum spin speed | 1400 RPM |
| Minimum spin speed | 400 RPM |
| Noise level (spin) | 72 dB |
| Noise level (wash) | 53 dB |
| Number of washing programs | 14 |
| Energy efficiency scale | A to G |
| Water consumption per cycle | 50 L |
| Energy consumption washing per cycle | 0.66 kWh |
| Package depth | 660 mm |
| Package width | 670 mm |
| Package height | 890 mm |
| Package weight | 67000 g |
Weight and Dimensions| Depth | 550 mm |
|---|---|
| Width | 600 mm |
| Height | 850 mm |
| Weight | 68000 g |
