To Next Page
G
Grant HansonAug 7, 2025
Why does my Samsung WW90T554DAW show an unbalance error?
- EeleeAug 8, 2025
The unbalance error on your Samsung Washer is caused by the laundry load. Check the laundry to resolve this issue, as this occurs by laundry.
Why does my Samsung WW90T554DAW show an unbalance error?
The unbalance error on your Samsung Washer is caused by the laundry load. Check the laundry to resolve this issue, as this occurs by laundry.
Why is there no water supply in my Samsung WW90T554DAW Washer?
If your Samsung Washer isn't getting water, it could be due to several reasons. Foreign material may be entering the water supply valve, or the water supply valve terminal might not be connected properly. The warm water and rinse connectors could be wrongly connected. Also, check if the PCB terminal from the drain hose to the detergent drawer is not connected, or if the transparent hose is folded or torn. Low water pressure, or a frozen water valve in winter, can also cause this issue. In this case, the water supply valve may be faulty.
Why does my Samsung Washer overflow?
Your Samsung Washer may be overflowing due to a few potential issues. It could be that water is supplied continually because the water level detection isn't working, possibly due to a clogged drain hose or an injection error. Freezing or foreign material in the water supply valve can also cause continuous water supply. A faulty sensor, or a blocked or damaged pressure tube might also be responsible. All these scenarios can be related to a water level sensor fault.
Why is the water level wrong in my Samsung Washer?
If the water level in your Samsung Washer is incorrect, it could be due to several reasons. The hose where the water level sensor is located might be damaged, clogged with foreign material, or folded. Too much lubricant on the air hose insertion part, a hose engagement error, a part fault (like faulty internal soldering), a disengaged water level sensor terminal, or a main PBA fault can also cause this. These issues point to a water level sensor fault.
Why is my Samsung Washer heater not working?
If the heater in your Samsung Washer isn't working, it could be due to a short-circuited washing heater or a disconnected wire. There might be a contact error or temperature sensor fault in the washing heater inside the tub. Also, if the water level sensor operates without water (due to frozen water or another reason) and the temperature sensor detects a high temperature (100 to 150 ?C), the washing machine will turn off the input power. This suggests a heater fault.
What causes communication errors in a Samsung Washer?
Communication errors in your Samsung Washer can occur if the signals between the sub and main PBAs are not sensed. Check the connector connections between the sub and main PBAs carefully and look for any faulty soldering after removing the sub PBA C/Panel. These issues may indicate a Main PCB and Sub PCB Signal Detection fault or a Main PCB and Sub PCB wire connection fault.
Instructions for safe operation and hazard prevention during servicing.
Detailed technical specifications for various washing machine models.
Comparison of features and specifications across different washing machine models.
Specifications for optional parts and accessories.
List of tools required for disassembly and reassembly procedures.
Step-by-step visual guide for disassembling washing machine components.
Explanation of information codes displayed during abnormal conditions and their causes/corrections.
Common problems and their solutions for washing machine operation.
Schematic diagram illustrating the basic wiring connections of the washing machine.
Wiring diagram specifically for models with LED displays.
Wiring diagram for washing machines equipped with Q-Drive technology.
Details on model naming conventions and project structure for WW6000T series.
Definitions of key terms and components used in the service manual.
General| Door color | Black |
|---|---|
| Door hinge | Left |
| Control type | Rotary |
| Loading type | Front-load |
| Product color | White |
| Built-in display | Yes |
| Custom panel-ready | - |
| Appliance placement | Freestanding |
| Lower built-in capability (topless) | No |
| Drum capacity | 9 kg |
| Cycle time (max) | 228 min |
| Spin-drying class | B |
| Maximum spin speed | 1400 RPM |
| Minimum spin speed | 400 RPM |
| Noise level (spin) | 72 dB |
| Noise level (wash) | 53 dB |
| Energy efficiency scale | A to G |
| Water consumption per cycle | 50 L |
| Energy consumption washing per cycle | - kWh |
| Package depth | 660 mm |
| Package width | 670 mm |
| Package height | 890 mm |
| Package weight | 69000 g |
| Repairability index | 9.6 |
Weight and Dimensions| Depth | 550 mm |
|---|---|
| Width | 600 mm |
| Height | 850 mm |
| Weight | 67000 g |
