Sanyo C7 - Page 7

11.
Fast
forward/Cue/AMSS
button
(F
FWD/
20.
Treble
controt
(TRE)
CUE/AMSS)
21.
Balance
contro!
(BAL)
12.
Stop
button
(STOP)
22.
Volume
contro!
{VOL)
13.
Pause
button
and
its
indicator
(PAUSE)
23.
Tape
counter
and
reset
button
(COUNTER)
14.
Microphone
input
socket
(MIC)
24,
Cassette
compartment
lid
15.
Microphone
mixing
volume
control
(MIC
MIX
25.
Speaker
terminals
(GPEAKER}
VOL)
26.
DC
input
socket
(DC
IN)
16.
Function
selectors
(TAPE/TUNER/PHONO)
27.
Beat
cancel
switch
(BEAT
CANCEL)
17.
AMSS
button
and
its
indicators
(AMSS)
28.
Tuner
input
socket
(TUNER)
18.
Loudness
control
switch
(LOUDNESS)
29.
Phono
input
sockets
(PHONO)
19,
Bass
control
(BASS)
30.
Earth
terminal
(GND)
CONNECTIONS AND POWER SUPPLY (Fig. 10) a:
Connect
the
components
as
shown
in
Fig.
10.
POWER
SUPPLY
UNIT
Inserting
the
batteries
:
1.
Open
the
battery
compartment
lid
by
sliding
the
OPEN
knob
in
the
direction
of
the
arrows
(Fig.
11).
2.
Take
out
the
battery
case
by
pulling
up
the
tape
as
shown
in
Fig.
12a
and
install
9
“D”
size
(UM—1)
flashlight
batteries
exactly
as
shown
in
Fig.
12b.
;
,
3.
Insert
the
battery
case
to
the
battery
compartment
exactly
as
shown
in
Fig.
13a
and
fix
it
by
pressing
the
protrusion
as
shown
in
Fig.
13b.
4. Close the battery compartment lid.
External
DC
input
socket
(EXT
DC
12
—
15
V)
:
pie
NOTE:
oa
The
centre
pin
of
this
socket
is
negative.
Sse
1.
Connect
the
plug
of
a
car
adaptor
(SANYO
model
CA-12
optional
extra)
to
the
socket.
2.
The
internal
battery
circuit
is
automaticaliy
disconnected.
AC input socket (AC)
NOTE:
* Do not connect the mains lead to an AC outlet until after all connections have been made.
*
Before
connecting
the
mains
lead,
set
the
POWER
switch
to
the.off”
position.
1.
Before
operating
the
unit
for
the
first
time
in
a
new
aréa,
it
is
essential
to
assure
that
the
setting
of
the
VOLTAGE
SELECTOR
(located
on the
bottom
of
the
unit)
corresponds
to
the
local
voltage.
To
adjust
the
voltage, reset
the
VOLTAGE
SELECTOR
io
correspond
with
the
local voltage (Fig.
14).
. Connect one end of the mains tead to the “AC” input socket and the other end to an AC outlet. |
3. When the mains lead is connected to the “AC” input socket, the batteries are automatically |
if
nN
disconnected.
DC output lead (DC OUT)
Connect this lead to the “DC IN” socket of the cassette deck/amplifier unit.
CAUTION
THIS DC OUTPUT LEAD IS DESIGNED ONLY FOR USE WITH MODEL C7p CASSETTE DECK/
AMPLIFIER UNIT. DO NOT USE WITH OTHER APPLIANCES.