Setting the RF output channel
If channel 3 is already occupied for
broadcasting,
1
Set your TV to channel 4.
2
Insert a pre-recorded tape into
this unit.
3
Press the OUTPUT button on
the DVD+VCR so that the VCR
OUTPUT light is lit.
• If noise appears on the TV screen, press the
VCR/TV button on the remote control.
4
Press the PLAY button once.
5
After a few seconds, press the PLAY button on the
DVD+VCR for 3 seconds.
• The RF output channel will change to channel 4
from channel 3 and you will see a playback pic-
ture.
• When a picture does not appear on the TV screen,
repeat step [4].
6
Press the STOP button to stop playback.
Initial Programming
1
Press the POWER button and the
language menu will appear.
2
Press the ▲/▼ button to select
language for VCR on-screen
display. Then press the B but-
ton.
3
Press the B button again to
begin channel programming.
“AUTO SET UP” will flash.
4
Please wait for a few minutes.
After scanning, the tuner stops on
the lowest memorized channel.
•For details, refer to the Instruction Manual.
VCR
Press the VCR button first.
DVD Player & Video Cassette Recorder
DVW-7100A
Thank you for buying Sanyo.
This guide will enable the quick and easy
setup of your new DVD+VCR, simply follow
the procedures inside.
For further details of features, please refer to
the instruction manual.
Is Everything In The Box?
• Remote control
(NA228UD)
with two AA batteries
• RF cable • Audio/Video
cables
• Instruction
manual
1 Connecting
DEW CAUTION
Condensation can form inside the DVD+VCR when it is suddenly moved from a cold place to a warm
or humid environment. In any such circumstance do not use this DVD+VCR approximately 2 hours
allowing complete elimination of any condensation.
AUDIO IN
VIDEO IN
ANTENNA
INPUT
R
L
DIGITAL
AUDIO OUT
COAXIAL
ANT-OUT
ANT-IN
AUDIO
OUT
DVD VCR
DVD/VCR
S-VIDEO
OUT
COMPONENT
VIDEO OUT
AUDIO IN
VIDEO IN
AUDIO OUT
VIDEO OUT
L
LY
R
R
CB/
P
B
CR/
P
R
AUDIO IN
VIDEO IN
ANTENNA
INPUT
R
L
Rear of TV
RF Cable
Video Cable
Audio Cable
RF Cable
Antenna
Rear of DVD+VCR
2
Setting the RF Output Channel and Initial Programming
STOP
PLAY
123
456
789
0 +10
POWER
SPEED
AUDIO
DISPLAY
SLOW
PAUSE
ENTER
MENU
TOP MENU
SETUP
MODE V.SURR
SEARCH
MODE
A
-
B
REPEAT
ANGLE
SUBTITLE
T-SET
DVD
REC OTR
VCR TV
SKIP CH.
CLEAR
C.RESET
VCR
RETURN
DVD/VCR select button
Select the output source (DVD or
VCR) to view on the TV screen.
To use a VCR, first press the VCR button.
To use a DVD, first press the DVD button.
3 Setting the Clock
1
Press the MENU button and the
MAIN menu will appear.
• If the clock is not set, the CLOCK
SET screen appears when you
press the MENU button. In this
case, go to step [3].
2
Press the o/p button to choose
the CLOCK SET menu. Press the
B button and the CLOCK SET
menu will appear.
3
Press the o/p button to choose
the month. Press the B button.
4
Press the o/p button to choose
the day. Press the B button.
5
Press the o/p button to choose
the year. Press the B button.
6
Press the o/p button to choose
the hour. Press the B button.
7
Press the o/p button to
choose the minute. Press
the B button.
8
Press the o/p button to choose
the AM or PM.
9
Press the B button when fin-
ished.
VCR
Press the VCR button first.
-MENU-
B TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
CLOCK SET
MONTH DAY YEAR
1 0 / – – – – – –
HOUR MINUTE AM/PM
– – : – –– –
-MENU-
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
CLOCK SET
MONTH DAY YEAR
1 0 / 0 1 2 0 0 4
HOUR MINUTE AM/PM
– – : – – – –
• •
• • • • • •
CLOCK SET
MONTH DAY YEAR
1 0 / 0 1 FRI 2 0 0 4
HOUR MINUTE AM/PM
0 5 : 4 0 P M AM
B PM
Printed in China 81VMN20318--- /
H9680UD ★★★★★
Need help? Call
1-800-813-3435
Weekdays 7:30 AM – 4:00 PM Central Time
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
CH 01
AUTO SET UP
Inserting the Batteries
Your REMOTE CONTROL HANDSET
is powered by two AA type batteries.
1
To insert them, push the tab back-
wards and lift off the cover of the
handset.
2
Put the two batteries into the compartment mak-
ing sure the + and – are correctly positioned.
3
Replace the cover.
• Quick
start guide
TIP:
•To change the on-screen language for
DVDfunction, refer to page 20 in the
Instruction Manual.
H9680UD_QG.qxd3 04.8.9 10:13 PM Page 1
To Next Page
Need help?
General
