What to do if the chamber temperature does not match the set value in Sanyo Laboratory Equipment?
If the chamber temperature of your Sanyo Laboratory Equipment does not match the set value, first, check if the ambient temperature is less than 5°C different from the set chamber temperature. Then, ensure that the outer door is closed tightly and that the gastight split doors or inner door are not left open.
How to fix the chamber temperature if it does not rise in Sanyo Laboratory Equipment?
If the chamber temperature of your Sanyo Laboratory Equipment isn't rising, ensure there's enough sterile distilled water in the humidifying pan.
Why is the gas concentration slow to recover in my Sanyo Medical Equipment?
The Incubator uses a HEPA filter for the gas piping. If the gas concentration recovers slowly when the CO2 gas concentration is normal, the HEPA filter may be clogged. Consult a Sanyo representative or agent. Also, check if the gas cylinder is low, the CO2 gas pressure regulator's secondary pressure is at 0.03 MPaG (0.3 kgf/cm2G, 4.3 psiG), the N2 gas pressure regulator's secondary pressure is at 0.05 MPaG (0.5 kgf/cm2G, 7.1 psiG), and if the gas tube is blocked.
How to unlock the outer door of Sanyo MCO-19MUVH?
When the power is OFF, the electric lock engages, preventing the outer door from opening. Turn the power ON or use the accessory unlock key to override the electric lock. Note that the outer door is also electrically locked during decontamination.
What to do if H2O2 decontamination cannot be performed on Sanyo MCO-19MUVH Medical Equipment?
If using the MCO-19M(UV)/19M, check if the optional MCO-HL is installed. If using the MCO-19M, confirm that both the optional MCO-HL and MCO-19UVS are installed. Verify that the UV lamp is not burned out, as this prevents H2O2 decontamination. Ensure the H2O2 Generator cable is properly connected, that the entire bottle of H2O2 Decontamination Reagent has not been used, and that the upper limit temperature alarm is not set to 50°C or higher.
What to do if the gas concentration does not match the set value in Sanyo MCO-19MUVH Medical Equipment?
Verify that the secondary pressure for the CO2 gas pressure regulator is at the specified value of 0.03 MPaG (0.3 kgf/cm2G, 4.3 psiG) and the secondary pressure for the N2 gas pressure regulator is at the specified value of 0.05 MPaG (0.5 kgf/cm2G, 7.1 psiG). Also, check if the gas tube is blocked.
Why is a large quantity of gas being consumed by my Sanyo Medical Equipment?
Check if the doors are being frequently opened and closed. Inspect gas connectors for leaks due to gas tube deterioration or pinhole leaks; consider replacing the gas tube annually. Also, check the packing seals for the gastight split doors and inner door for defects, and ensure the access hole is closed.
What to do if Sanyo Medical Equipment Incubator does not operate at all?
First, verify that the Incubator is properly plugged in. Then, check for any power outages or tripped circuit breakers that may be interrupting the power supply.
General| Type | CO2 Incubator |
|---|---|
| Temperature Range | Ambient +5°C to 50°C |
| Temperature Control | ±0.1°C |
| CO2 Range | 0 to 20% |
| Humidity Range | Up to 95% RH |
| Interior Volume | 170 liters |
| Capacity | 6.0 cubic feet |
| CO2 Control Accuracy | ±0.1% |
| Power Supply | 50/60Hz |
| External Dimensions (WxDxH) | 620 x 715 x 905 mm |
| Internal Dimensions (WxDxH) | 490 x 505 x 690 mm (19.3 x 19.9 x 27.2 in) |
To Next Page
