Scag Power Equipment STCII-61V-36BV User Manual

Scag Power Equipment STCII-61V-36BV

97 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

PART NO. 03549

PRINTED 9/2023

PRINTED IN USA

© 2023

Scag Power Equipment

Division of Metalcraft of Mayville, Inc.

Congratulations on owning a Scag mower! This manual contains the operating

instructions and safety information for your Scag mower. Reading this manual

can provide you with assistance in maintenance and adjustment procedures to

keep your mower performing to maximum efciency. The specic models that

this book covers are listed on the inside cover. Before operating your machine,

please read all the information enclosed.

OPERATOR’S

MANUAL

Models: STCII-48V-22FX

STCII-48V-23CV

STCII-52V-23FX

STCII-52V-24FT

STCII-52V-25CV-EFI

STCII-52V-26FT-EFI

STCII-52V-28BV-EFI

STCII-61V-26CV-EFI

STCII-61V-26FT-EFI

STCII-61V-27FX

STCII-61V-36BV

Table of Contents

Questions and Answers:

B
bwillisSep 2, 2025
Why is my Scag Power Equipment STCII-61V-36BV leaving stringers or occasional blades of uncut grass?
- D
  Dustin ConradSep 2, 2025
  If your Scag Power Equipment Lawn Mower is leaving occasional blades of uncut grass, several factors could be responsible. Ensure the engine is running at full RPM. If the ground speed is too fast, slow down to adjust for conditions. Avoid cutting wet grass; wait until it has dried out. Check the blades; dull or incorrectly sharpened blades need sharpening. A plugged deck due to grass accumulation requires cleaning the underside of the deck. Finally, slipping belts require adjusting the belt tension.
J
John CollinsAug 31, 2025
What to do if my Scag Power Equipment STCII-61V-36BV is scalping, hitting dirt, or cutting too close to the ground?
- D
  Danielle RamirezSep 1, 2025
  If your Scag Power Equipment Lawn Mower blades are hitting the dirt or cutting too close to the ground, check and adjust the tire pressures, as low tire pressure could be the cause. If the ground speed is too fast, slow down to adjust for the conditions. Also, check if you are cutting too low; you may need to reduce ground speed, raise the cutting height, or change the direction of the cut and/or change the pitch and level. If you are mowing on rough terrain, you may need to reduce ground speed, raise the cutting height, and/or change the direction of the cut. Cutting wet grass can also cause scalping, so cut the grass after it has dried out.
C
Casey MorrisAug 30, 2025
Why is my Scag Power Equipment STCII-61V-36BV Lawn Mower leaving strips of uncut grass in cutting path?
- T
  Tony MilesAug 30, 2025
  If your Scag Power Equipment Lawn Mower is leaving strips of uncut grass, it could be due to several reasons. The blades might be dull or worn, or they may have been sharpened incorrectly, so try sharpening the blades. The engine RPM may be too low, so run the engine at full RPM. The belt might be slipping, so adjust the belt tension. The deck could be plugged with grass, so clean the underside of the deck. The ground speed may be too fast, so slow down to adjust for conditions. If the grass is wet, cut it after it has dried out. Finally, the blades might be bent, so replace them.
J
justinoconnorAug 29, 2025
Why is Scag Power Equipment STCII-61V-36BV leaving a sloping ridge across cutting path?
- R
  Rebecca NielsenAug 29, 2025
  If your Scag Power Equipment Lawn Mower is leaving a sloping ridge across the width of the cutting path, start by checking and adjusting the tire pressure to ensure they are equal. Uneven wheels can also cause this issue, so verify their alignment. If the problem persists, consult an authorized SCAG dealer.
V
victoriamartinezAug 27, 2025
Why is Scag Power Equipment Lawn Mower streaking (strips of uncut grass between cutting paths)?
- J
  Jeremy AllenAug 27, 2025
  If your Scag Power Equipment Lawn Mower is leaving strips of uncut grass between cutting paths, increase the overlap of each pass.
J
John ThomasAug 27, 2025
What to do if Scag Power Equipment Lawn Mower is scalping (blades hitting dirt)?
- B
  Bethany TannerAug 27, 2025
  If your Scag Power Equipment Lawn Mower is scalping, meaning the blades are hitting the dirt or cutting too close to the ground, check and adjust tire pressures. Slow down your ground speed, especially in rough conditions. You might need to raise the cutting height or change the direction you're cutting. Avoid cutting wet grass. These adjustments should help prevent scalping.
Q
qparkerAug 25, 2025
What to do if my Scag Power Equipment STCII-61V-36BV is streaking (strips of uncut grass in cutting path)?
- C
  Cynthia EspinozaAug 26, 2025
  If your Scag Power Equipment Lawn Mower is leaving strips of uncut grass in the cutting path, it could be due to several factors. Dull or worn blades are a common cause, so start by sharpening them. Also, make sure the engine is running at full RPM. Check for a slipping belt and adjust the tension if needed. Excess grass accumulation under the deck can also cause streaking, so clean it thoroughly. Reduce your ground speed, especially if the grass is wet, and consider replacing bent blades.
B
Brenda HernandezAug 23, 2025
What to do if my Scag Power Equipment STCII-61V-36BV leaves stringers (occasional blades of uncut grass)?
- J
  Jacob EwingAug 23, 2025
  If your lawn mower is leaving occasional blades of uncut grass, several factors could be responsible. Make sure the engine is running at full RPM. If you're moving too fast, slow down to suit the conditions. Avoid cutting wet grass, as this can also cause the issue. Ensure your blades are sharp and correctly sharpened. Also, check for grass accumulation under the deck and clean it if necessary. Slipping belts could be the cause, so adjust the belt tension.

Scag Power Equipment STCII-61V-36BV Specifications

General

Brand	Scag Power Equipment
Model	STCII-61V-36BV
Category	Lawn Mower
Language	English

Related product manuals

Tiger Cat II STCII-61V-23FX

Tiger Cat II STCII-61V-29CV-EFI

Preview: STCII-48V-26MX

Preview: Tiger Cat II STCII-48V-22FS

Tiger Cat II STCII-48V-22FS

Tiger Cat II STCII-52V-22FX

Preview: Tiger Cat II STCII-48V-22FX

Tiger Cat II STCII-48V-22FX

Scag Power Equipment STC52A-23KA

Scag Power Equipment STC61V-25CV

Preview: STC48V-19KAI

Tiger Cat STC61V-27CV

Preview: TIGER CAT STC48V-22FS

TIGER CAT STC48V-22FS

Tiger Cat STC52V-27CV-SS