Scag Power Equipment Tiger Cat STC52V-27CV-SS User Manual

PART NO. 03250 Rev.4
PRINTED 11/2009
PRINTED IN USA
© 2009
Scag Power Equipment
Division of Metalcraft of Mayville, Inc.
Congratulations on owning a Scag mower! This manual contains the operating
instructions and safety information for your Scag mower. Reading this manual
can provide you with assistance in maintenance and adjustment procedures to
keep your mower performing to maximum effi ciency. The specifi c models that
this book covers are listed on the inside cover. Before operating your machine,
please read all the information enclosed.
OPERATOR’S
MANUAL
Tiger Cat
Models: STC48V-19KAI
STC48V-23CV
STC48V-25CV
STC48V-25CV-SS
STC48V-26BS
STC52V-25CV
STC52V-27CV
STC52V-27CV-SS
STC61V-25CV
STC61V-27CV
STC61V-27CV-SS

Scag Power Equipment Tiger Cat STC52V-27CV-SS Specifications

General

Category	Lawn Mower
Manufacturer	Scag Power Equipment
Model	Tiger Cat STC52V-27CV-SS
Cutting Width	52 inches
Transmission	Hydrostatic
Weight	1, 100 lbs
Turning Radius	Zero-turn
Speed Range	0-10 mph
Blade Engagement	Electric
Horsepower	27 hp
Tire Size Rear	23x9.50-12

Summary

OPERATOR'S MANUAL

SECTION 1 - GENERAL INFORMATION

1.1 Introduction

General introduction to the mower and manual.

1.2 Direction Reference

Defines front, rear, left, and right from the operator's perspective.

SECTION 2 - SAFETY INFORMATION

2.1 Introduction

Operator's role in safety and manual importance.

2.2 Signal Words

Explains danger, warning, caution signal words used in manual.

2.3 Before Operation Considerations

Safety considerations before operating the mower.

2.4 Operation Considerations

Safety considerations during mower operation.

SECTION 3 - SPECIFICATIONS

3.1 Engine

Engine specifications including horsepower and type.

3.2 Electrical

Electrical system specifications including battery and charging.

3.3 Tractor

Tractor system specifications like drive and steering.

SECTION 4 - OPERATING INSTRUCTIONS

4.1 Controls and Instrument Identification

Identification of mower controls and instruments.

4.2 Safety Interlock System

Explanation of the safety interlock system preventing operation.

4.3 Initial Run-In Procedures

Procedures for the first 20 hours of operation.

4.4 Starting the Engine

Step-by-step guide to starting the engine safely.

SECTION 5 - TROUBLESHOOTING CUTTING CONDITIONS

Stringers - Occasional Blades of Uncut Grass

Identifies uncut grass strips and their causes/cures.

Streaking - Strips of Uncut Grass in Cutting Path

Identifies streaking and its causes/cures.

Uneven Cut on Flat Ground

Identifies uneven cuts and their causes/cures.

Scalping - Blades Hitting Dirt

Identifies scalping and its causes/cures.

SECTION 6 - ADJUSTMENTS

6.1 Parking Brake Adjustment

Procedures for adjusting the parking brake linkage.

6.2 Travel Adjustments

Adjustments for neutral and tracking of drive wheels.

6.3 Throttle Control and Choke Adjustments

Adjustments for throttle and choke controls.

6.6 Cutter Deck Adjustments

Adjustments for cutter deck level, pitch, and height.

SECTION 7 - MAINTENANCE

7.1 Maintenance Chart - Recommended Service Intervals

Schedule for maintenance tasks based on operating hours.

7.2 Lubrication

Grease fitting lubrication chart and procedures.

7.3 Hydraulic System

Checking and changing hydraulic oil and filter.

7.4 Engine Oil

Checking and changing engine oil and filter.

SECTION 8 - ILLUSTRATED PARTS LIST

8.1 SCAG Approved Attachments and Accessories

List of approved attachments and accessories with part numbers.

48V & 52V Cutter Decks

Illustrated parts breakdown for 48V and 52V cutter decks.

61V Cutter Deck

Illustrated parts breakdown for the 61V cutter deck.

Cutter Deck Controls

Illustrated parts for cutter deck control mechanisms.