Scag Power Equipment Turf Tiger Propane STT52V-25CH-LP User Manual (English)

Questions and Answers:

W
William MyersAug 14, 2025
Why is my Scag Power Equipment Lawn Mower streaking?
- L
  Leslie SchneiderAug 14, 2025
  If your Scag Power Equipment Lawn Mower is leaving strips of uncut grass in the cutting path, make sure that the blades are sharp. Dull or incorrectly sharpened blades can cause this issue. Also, ensure that the engine is running at full RPM and that the mower belt isn't slipping by adjusting the belt tension. A deck plugged with grass accumulation can also cause streaking, so clean the underside of the deck. Avoid mowing wet grass and reduce ground speed to suit the conditions. Bent blades should be replaced.
R
Reginald MccormickAug 17, 2025
How to fix stringers with Scag Power Equipment Lawn Mower?
- S
  Sara WhiteAug 17, 2025
  To address occasional blades of uncut grass with your Scag Power Equipment Lawn Mower, ensure the engine is running at full RPM and reduce ground speed to match the conditions. Avoid cutting wet grass, and sharpen dull blades. Clear any grass accumulation from the underside of the deck and adjust the belt tension if it's slipping.
A
Alexander TaylorAug 20, 2025
What to do if Scag Power Equipment Lawn Mower is scalping?
- A
  allisonmeyerAug 20, 2025
  If your Scag Power Equipment Lawn Mower is scalping, check and adjust tire pressures, and slow down if your ground speed is too fast. If you are cutting too low, you may need to reduce ground speed, raise the cutting height, and/or change the direction of cut. Also, consider adjusting the pitch and level. Avoid mowing wet grass.
J
Jeremy KnightAug 25, 2025
How to fix uneven cut on flat ground with Scag Power Equipment Lawn Mower?
- D
  Dawn JonesAug 25, 2025
  To correct an uneven cut on flat ground with your Scag Power Equipment Lawn Mower, replace the blade if the lift is worn. Ensure the blade is mounted with the cutting edge toward the ground and clean any grass accumulation from the underside of the deck. Adjust the deck pitch and level if there's too much blade angle. For issues related to improper deck mounting or a bent spindle area, consult an authorized SCAG dealer. Also, ensure that the blade is sharp.
K
Kimberly GilbertAug 27, 2025
How to fix sloping ridge with Scag Power Equipment Lawn Mower?
- B
  Brittney CastilloAug 27, 2025
  To fix a sloping ridge across the cutting path with your Scag Power Equipment Lawn Mower, check and adjust tire pressure to ensure they are equal. Also, make sure the deck is level side to side. If the deck is mounted incorrectly, consult your authorized SCAG dealer.
A
Amanda KellyAug 30, 2025
How to fix step cut with Scag Power Equipment Lawn Mower?
- C
  Charles CaseyAug 30, 2025
  To resolve a step cut (ridge in the center of the cutting path) with your Scag Power Equipment Lawn Mower, adjust the pitch and level to ensure the blades are mounted evenly. Replace the blade if it's bent. If you suspect an internal spindle failure or incorrect spindle mounting, consult your authorized SCAG dealer.
R
Rebecca GravesSep 2, 2025
What causes slope cut with Scag Power Equipment Lawn Mower?
- L
  Lauren LambSep 2, 2025
  If you observe sloping ridges across the cutting path of your Scag Power Equipment Lawn Mower, it may indicate a bent spindle mounting area, internal spindle failure, or a bent deck housing. For these issues, it is recommended to consult your authorized SCAG dealer.
R
robertkingSep 6, 2025
What to do if Scag Power Equipment Lawn Mower has uneven cut on uneven ground?
- S
  Scott CampbellSep 6, 2025
  To address an uneven cut on uneven ground with your Scag Power Equipment Lawn Mower, you may need to reduce ground speed, raise the cutting height, and/or change the direction of cut.
V
Victor MurraySep 9, 2025
How to prevent strips of uncut grass with Scag Power Equipment Lawn Mower?
- R
  randyhuntSep 9, 2025
  To prevent strips of uncut grass between cutting paths with your Scag Power Equipment Lawn Mower, increase the overlap of each pass.

Scag Power Equipment Turf Tiger Propane STT52V-25CH-LP Specifications

General

Cutting Width	52 inches
Fuel Type	Propane
Turning Radius	Zero-turn
Warranty	3 years
Speed	Forward: 12 mph, Reverse: 5 mph
Blade Engagement	Electric
Tire Size Front	13 x 6.5 - 6
Tire Size Rear	24 x 12 - 12
Engine	Kohler Command Pro Propane CH740