To Next PageTo Next PageHow to fix sloping ridge across cutting path with Scag Power Equipment Lawn Mower?
If your Scag Power Equipment Lawn Mower is leaving a sloping ridge across the width of the cutting path, check and adjust tire pressure to ensure they are equal. Also, verify that the wheels are even. If the deck is mounted incorrectly, or is not level side-to-side, consult your authorized SCAG dealer.
How to fix occasional blades of uncut grass with my Scag Power Equipment Lawn Mower?
If your Scag Power Equipment Lawn Mower is leaving occasional blades of uncut grass, there are several possible causes. Ensure the engine is running at full RPM. If your ground speed is too fast, slow down. Cutting wet grass can cause this, so cut after it has dried. Dull blades or incorrect sharpening can be a factor, so sharpen the blades. Also, grass accumulation under the deck can cause this, so clean the underside of the deck. Finally, check for belts slipping and adjust the belt tension if needed.
Why is my Scag Power Equipment Turf Tiger STT-29DFI-SS Lawn Mower cutting unevenly on flat ground?
If your Scag Power Equipment Lawn Mower is producing an uneven cut on flat ground, resulting in a wavy, high-low appearance, scalloped cut, or rough contour, several factors could be responsible. If the lift is worn from the blade, replace the blade. Ensure the blade is mounted with the cutting edge toward the ground. Clean any grass accumulation from the underside of the deck. Adjust the deck pitch and level if there's too much blade angle. If the deck is mounted improperly or the spindle area is bent, consult your authorized SCAG dealer for assistance. Finally, a dull blade can cause this issue, so sharpen the blade.
Why is my Scag Power Equipment Turf Tiger STT-29DFI-SS Lawn Mower streaking?
If your Scag Power Equipment Lawn Mower is leaving strips of uncut grass in the cutting path, several factors could be responsible. The blades may be dull or worn, or they might be incorrectly sharpened, so start by sharpening the blades. Also, ensure the engine is running at full RPM. Check for belt slippage and adjust belt tension if needed. Grass accumulation under the deck can also cause this, so clean the underside of the deck. Avoid mowing wet grass, and slow down if your ground speed is too fast. Finally, inspect the blades for bending and replace them if necessary.
How to fix stringers (occasional blades of uncut grass) with Scag Power Equipment Lawn Mower?
If your Scag Power Equipment Lawn Mower is leaving occasional blades of uncut grass, there are several possible reasons. Ensure the engine is running at full RPM. If your ground speed is too fast, slow down. Avoid cutting wet grass; wait until it dries out. Sharpen dull blades. Clean any grass accumulation from the underside of the deck. Finally, check for and adjust belt tension if the belts are slipping.
What to do if my Scag Power Equipment Turf Tiger STT-29DFI-SS Lawn Mower is scalping?
If your Scag Power Equipment Lawn Mower blades are hitting the dirt or cutting too close to the ground, check and adjust the tire pressures. Reduce ground speed if it's too fast. If you are cutting too low, you may need to reduce ground speed, raise the cutting height, change the direction of cut, and/or change the pitch and level. These issues can also arise on rough terrain, so consider reducing speed, raising the cutting height, and/or changing the direction of cut. Cutting wet grass can also cause scalping, so allow the grass to dry before cutting.
Why is my Scag Power Equipment Lawn Mower leaving stringers or occasional blades of uncut grass?
Stringers, or occasional blades of uncut grass, can be caused by several factors. A low engine RPM requires you to run the engine at full RPM. If the ground speed is too fast, slow down to adjust for conditions. Avoid wet grass by cutting after it has dried out. Dull blades or incorrect sharpening require you to sharpen the blades. Grass accumulation under the deck requires you to clean the underside of the deck. A slipping belt requires you to adjust the belt tension.
What to do if my Scag Power Equipment Lawn Mower has an uneven cut on flat ground?
An uneven cut on flat ground, resulting in a wavy, high-low appearance, scalloped cut, or rough contour, can be caused by several issues. If the lift is worn from the blade, replace the blade. Ensure the blade is mounted with the cutting edge toward the ground, not upside down. Grass accumulation under the deck requires you to clean the underside of the deck. If there is too much blade angle (deck pitch), adjust the pitch and level. A dull blade requires you to sharpen it. For an improperly mounted deck or bent spindle area, consult your authorized SCAG dealer.
Why Scag Power Equipment Lawn Mower leaves an uneven cut on flat ground?
If your Scag Power Equipment Lawn Mower is producing an uneven cut on flat ground, resulting in a wavy, high-low appearance, scalloped cut, or rough contour, several factors could be at play. If the lift is worn from the blade, replace the blade. Ensure the blade is mounted correctly with the cutting edge toward the ground. Clean any grass accumulation from the underside of the deck. Adjust the deck pitch and level if there's too much blade angle. If the deck is mounted improperly or the spindle area is bent, consult your authorized SCAG dealer. Finally, sharpen the blade if it's dull.
What to do if my Scag Power Equipment Turf Tiger STT-29DFI-SS Lawn Mower leaves a ridge in the center of the cutting path?
If your Scag Power Equipment Lawn Mower is leaving a ridge in the center of the cutting path, the blades may not be mounted evenly, so adjust the pitch and level. Alternatively, the blade could be bent, so replace the blade. For internal spindle failure or incorrect mounting of the spindle, consult your authorized SCAG dealer.
General| Brand | Scag Power Equipment |
|---|---|
| Model | Turf Tiger STT-29DFI-SS |
| Category | Lawn Mower |
| Language | English |
Emphasizes operator safety, training, and responsibility for preventing accidents.
Explains the meaning and importance of signal words like DANGER, WARNING, and CAUTION.
Lists crucial pre-operation safety checks, rules, and prohibitions for safe use.
Lists crucial pre-operation safety checks, rules, and prohibitions for safe use.
Covers safety aspects of the ROPS, including its use and limitations.
Identifies and explains the function of all mower and engine controls and instruments.
Describes the safety system preventing engine start without proper conditions.
Provides step-by-step instructions for safely starting the mower's engine.
Explains how to operate the mower's travel and steering controls for smooth operation.
Details the procedure for engaging and disengaging the mower deck blades safely.
Provides critical safety precautions and operating guidelines for slopes.
Describes the safe method for clearing blockages in the discharge chute.
Details the step-by-step procedure for adjusting the cutter deck's cutting height.
Provides detailed instructions for adjusting the parking brake linkage for proper operation.
Provides a schedule of recommended maintenance tasks based on operating hours.
Covers blade inspection, sharpening, balancing, and replacement procedures.
Electrical schematic diagram for STT Kohler models.
Electrical schematic diagram for STT 27HP Kawasaki models.
Electrical schematic diagram for STT 29DFI Kawasaki models.
Electrical schematic diagram for STT 35BVAC Briggs & Stratton models.
Details the limited warranty terms and conditions for commercial equipment.
