www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB
|
17
Installing the folded lter (19) (g. 3+9)
For dry vacuuming, slide the folded lter (19) provided
over the lter basket with safety oat valve (15). The
folded lter (19) is only suitable for dry vacuuming!
Installing the paper lter bag (18) (g. 3+10)
It is recommended to use an additional paper lter
bag (18) when vacuuming ne, dry dirt.
• Slide the paper lter bag (18) over the suction open-
ing in the stainless steel container (9). The paper l-
ter bag (18) is only suitable for dry vacuuming. The
paper lter bag (18) makes it easier to dispose of
the dust collected.
Installing the suction hose (16) (g. 3+11+12)
Connect the suction hose (16) to the corresponding
port, depending on the desired use, on the wet and
dry vacuum.
Vacuuming:
Connect the suction hose (16) to the suction hose port
(10). To do so, slide the end of the suction hose (16)
with the two nipples into the suction hose port (10)
(A). Insert the two nipples into the recesses. Once
the suction hose is fully inserted, turn it clockwise (B).
Blowing:
Connect the suction hose (16) to the blowing func-
tion connection port (14). Slide the end of the suction
hose (15) with the two nipples into the blowing func-
tion connection port (14). Insert the two nipples into
the recesses. It is not necessary to turn it here.
Installing the metal extension tube (22), suction
hose (16) and nozzles (20/21) (g. 13)
• Connect the metal extension tube (22) with the bent
end of the suction hose (16).
• Fit the oor nozzle (20) or joint nozzle (21) to the
other end of the metal extension tube (22).
• Push the slide piece forwards (A) to change the
length of the metal extension tube (22). (Fig. 14)
• Pull the tube to the desired length (B). Ensure that
the slide lock latches into place. (Fig. 14)
Installing the bottom cable holder (g. 3+15)
• Clip the bottom cable holder (24) onto the wheel
mounting base (7) at the rear of the device. The
top cable holder (13) is on the connection port for
the blower function (14).
8. Operation
m WARNING!
Switch the device o if liquid or foam emerges with
the exhaust air during wet vacuuming.
Switch on / switch o / automatic (g. 16-17)
The ON/OFF switch (12) has three settings:
1 switch setting 0: O
6. Technical Data
Mains voltage 220-240V~ 50/60Hz
Power
1400W
Maximum device socket power
2000W
Total power
3400W
Water tank capacity 30L
Suction performance 20 Kpa
Protection category IPX4
Protection class I
7. Installation
m IMPORTANT!
Prior to use, ensure that the device has been cor-
rectly and fully assembled.
Unpacking (Fig. 1+2+3)
• Release the locking hooks (4) and remove the ma-
chine head (2). The accessories are located inside
the stainless steel container (9). Only the metal ex-
tension tube (22) is located outside the stainless steel
container (9) in the packaging. Remove all of the ac-
cessories from the stainless steel container (9).
Installing the castor mounts (5) (g. 4+5)
• Turn the stainless steel container (9) upside-down
(the machine head (2) must be removed).
• Push the castor mounts (5) into the cut-outs pro-
vided on the wheel mounting base (7). (4x)
• Fasten the castor mounts (5) with a screwdriver
(not included in the delivery) and one screw each
(23). (4x)
Installing the castors (6) (g. 6)
• Press the four castors (6) into the holes in the wheel
mounting base (5).
Installing the machine head (2) and the handle (1)
(Fig. 7)
• Place the machine head (2) on the stainless steel
container (9). Secure the machine head (2) with
the locking hooks (4). When installing the machine
head (2), ensure that the locking hooks (4) latch into
place correctly.
• Place the handle (1) on the machine head (2) and
fasten it with two screws (23) with a screwdriver
(not included in the delivery).
Installing the foam lter (17) (g. 3+8)
Never use the device without lter! Always ensure
that the lters are correctly tted!
• Installing the foam lter (17): For wet vacuuming,
slide the foam lter (17) provided over the lter bas-
ket with safety oat valve (15).
To Next Page
Loading...
Need help?
General
