EasyManua.ls Logo

Scheppach HC26 - User Manual

Scheppach HC26
96 pages
Go to English
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Nachdrucke, auch auszugsweise, bedürfen der Genehmigung.
Technische Änderungen vorbehalten. Abbildungen beispielhaft!
Art.Nr.
5906135901
AusgabeNr.
5906135901_0301
Rev.Nr.
02/08/2021
HC26
DE
Druckluftkompressor
Originalbedienungsanleitung
5
GB
Compressor
Translation of original instruction manual
17
EE
Suruõhukompressor
Originaalkäitusjuhendi tõlge
28
LT
Pneumatinis kompresorius
Originalios naudojimo instrukcijos vertimas
38
LV
Saspiestā gaisa kompresors
Oriģinālās lietošanas instrukcijas tulkojums
49
SE
Tryckluftskompressor
Översättning av original-bruksanvisning
60
FI
Paineilmakompressori
Käännös alkuperäisestä käyttöohjeesta
70
DK
Trykluftkompressor
Oversættelse fra den oprindelige betjeningsvejledning
81

Table of Contents

Other manuals for Scheppach HC26

Preview: Translation From The Original Instruction Manual
Translation From The Original Instruction Manual104 pages

Questions and Answers

  • W
    William WagnerAug 3, 2025
    What to do if my Scheppach HC26 Compressor does not start?
    • K
      Kevin PeckAug 4, 2025
      If your Scheppach Compressor isn't starting, there could be several reasons. First, check the supply voltage, power plug, and socket-outlet to ensure they're working. Also, make sure the extension cable isn't too long and has adequately sized wires to provide sufficient voltage. Operating the compressor when the outside temperature is below +5° C can also prevent it from starting, so ensure it's warmer than that. Finally, the motor might be overheated; allow it to cool down and address the cause of the overheating.
  • J
    jamiedeleonAug 8, 2025
    Why does my Scheppach HC26 Compressor start but there is no pressure?
    • J
      jimmy86Aug 8, 2025
      If your Scheppach Compressor starts but doesn't build pressure, it could be due to a few reasons. A leaking non-return valve could be the cause and should be replaced by a service center. Damaged seals can also cause this issue; have them checked and replaced, if necessary, by a service center. Additionally, check the drain plug for condensation water and tighten it by hand. Inspect the screw's seal and replace it if needed.
  • M
    Melinda BrownAug 13, 2025
    How to fix a Scheppach Compressor that starts but tools don't?
    • J
      Jennifer EvansAug 14, 2025
      If your Scheppach Compressor starts and the pressure gauge shows pressure, but your tools aren't working, the issue might be with the connections. Check the compressed air hose and tools for leaks, and replace them if necessary. Also, inspect the quick-lock coupling for leaks and replace it if needed.
  • B
    butlerryanAug 18, 2025
    What to do if my Scheppach Air Compressor does not start?
    • S
      Shannon AyersAug 18, 2025
      If your Scheppach Air Compressor isn't starting, several factors could be at play. First, check the supply voltage, power plug, and socket-outlet to ensure they're functioning correctly. Insufficient supply voltage could also be the culprit, so make sure your extension cable isn't too long and uses adequately sized wires. Another reason might be low outside temperature; avoid operating the compressor below +5° C. Lastly, the motor might be overheated; allow it to cool down and address the cause of overheating if necessary.
  • X
    xgreenAug 23, 2025
    Why does my Scheppach Air Compressor start but not build pressure?
    • C
      Charles MarshallAug 23, 2025
      If your Scheppach Air Compressor starts but doesn't build pressure, there are a few potential causes. One possibility is a leaking non-return valve, which would need replacement by a service center. Damaged seals could also be the issue; inspect them and have any damaged ones replaced by a service center. Finally, check the drain plug for condensation water; tighten it by hand and inspect/replace the seal if necessary.
  • J
    James OconnorAug 28, 2025
    How to troubleshoot if my Scheppach Air Compressor tools won't start even with pressure?
    • P
      Phillip HernandezAug 29, 2025
      If your Scheppach Air Compressor shows pressure but your tools aren't starting, the issue likely lies in the connections. Check the compressed air hose and tools for leaks, replacing them if needed. Also, inspect the quick-lock coupling for leaks and replace it if necessary.

Summary

Explanation of the symbols on the equipment

Introduction

Device description

Scope of delivery

Intended use

Safety information

Additional safety instructions

Further safety guidelines and warnings beyond the basic ones.

Safety instructions for working with compressed air and blasting guns

Specific safety precautions for using compressed air tools and blasting guns.

Safety instructions when using spraying attachments

Safety measures required when using spraying attachments like paint sprayers.

Operating pressure vessels

Guidelines for safe operation and maintenance of pressure vessels.

Technical data

Before starting the equipment

Attachment and operation

Fitting the wheels

Attaching the wheels to the compressor unit as shown in the diagram.

Fitting the supporting foot

Attaching the supporting foot to the compressor unit as shown in the diagram.

Installation of the air filter

Installing the air filter on the unit by turning clockwise.

Changing the transportation cover

Replacing the transport lid with the oil sealing plug for operation.

Checking the oil level

Verifying the oil level in the sight glass before first use.

Mains connection

Connecting the compressor to a suitable power socket.

ON;OFF switch

Operating the compressor by using the ON/OFF switch.

Setting the pressure switch

Information on the factory-set pressure switch cut-in and cut-out pressures.

Overload protection

Understanding the compressor's automatic thermal overload protection.

Electrical connection

Damaged electrical connection cable

Identifying and avoiding hazards from damaged electrical cables.

Cleaning, maintenance, and storage

Cleaning

Steps and recommendations for cleaning the compressor equipment.

Maintenance work on the pressure vessel; condensed water

Draining condensed water and checking the pressure vessel for damage.

Safety valve

Instructions for actuating the safety valve periodically to ensure it works.

Checking the oil level at regular intervals

How to check the oil level in the compressor at regular intervals.

Changing the oil

Procedure for draining and refilling the compressor oil.

Cleaning the intake filter

How to clean the air intake filter to maintain performance.

Storage

Proper procedures for storing the compressor to ensure safety.

Releasing excess pressure

Safely releasing any remaining compressed air from the vessel.

Service information

Information on wear parts and obtaining spare parts.

Disposal and recycling

Troubleshooting

CE Declaration of Conformity

Garantiebedingungen

Warranty conditions

These conditions govern manufacturer's warranty for new equipment for private consumers.

Warranty service

Warranty covers material or manufacturing defects, limited to repair or replacement.

Excluded from warranty services

List of conditions and damages not covered by warranty.

Warranty period

Details on warranty duration, commencement, and claim procedures.

For the assertion of your warranty claims

Contacting the service center for warranty claims and procedures.

Processing time

Expected processing time for warranty claims and communication.

Wear parts

Identification of wear parts excluded from warranty coverage.

Cost estimate

Procedures for repairs outside warranty and obtaining cost estimates.

Other claims

Limitations on other types of claims and governing language for terms.

Scheppach HC26 Specifications

General IconGeneral
ModelHC26
Max Pressure8 bar
Tank Capacity24 l
Weight24 kg
Voltage230 V
Power1.5 kW

Related product manuals