Scheppach HDA-14 User Manual

www.scheppach.com
GB
|
21
NOTE: Fasten the device at least 2.13m above the
oor.
Setting up the heavy-duty air lter
To ensure the device is operated properly through air
circulation, make sure there is a gap of at least 50cm
on both sides of the air intake and at least 10cm from
the air outlet to the wall.
Keep other electrical devices, such as radios and tele-
visions, at least 1m from the device.
Do not plug the mains plug into the same socket as one
with radios, televisions or other electrical devices. This
can cause the screen to icker or interference noises.
• Long-term use in the same place can make the walls
dirty.
• Ensure that the air intake and outlet are not covered
in order to ensure optimal air circulation and maxi-
mum performance.
9. Start up
m Attention!
Always make sure the device is fully assembled
before commissioning!
Switching on/o󰀨 (Fig. 4 - 5)
• Press the “ON/OFF” button on the remote control
(5) or on the control panel (1) in order to switch the
device on or o󰀨.
Timer function (Fig. 4 - 5)
The “TIME” button on the remote control (5) or on the
control panel (1) controls the three di󰀨erent time set-
tings:
• Press the “TIME” button once so that the device
switches o󰀨 automatically after one hour. (1H lamp
lights up on the control panel.)
• Press the “TIME” button twice so that the device
switches o󰀨 automatically after two hours. (2H lamp
lights up on the control panel.)
• Press the “TIME” button three-times so that the de-
vice switches o󰀨 automatically after four hours. (4H
lamp lights up on the control panel.)
Speed function (Fig. 4 - 5)
The “SPEED” button on the remote control (5) or on the
control panel (1) controls the three di󰀨erent air speeds.
• Press the “SPEED” button once so that the device
switches to the highest air speed.(HI lamp lights up
on the control panel.)
Noise and vibration
m Warning: Noise can have serious e󰀨ects on your
health. If the machine noise exceeds 85 dB (A), please
wear suitable hearing protection.
7. Unpacking
• Open the packaging and carefully remove the de-
vice.
• Remove the packaging material, as well as the pack-
aging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport
damage. In the event of complaints the carrier must
be informed immediately. Later claims will not be
recognised.
• If possible, keep the packaging until the expiry of the
warranty period.
• Familiarise yourself with the product by means of the
operating instructions before using for the rst time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Replace-
ment parts can be obtained from your dealer.
• When ordering please provide our article number as
well as type and year of manufacture for your equip-
ment.
m Attention!
The device and the packaging material are not
children’s toys! Do not let children play with plas-
tic bags, lms or small parts! There is a danger of
choking or su󰀨ocating!
8. Assembly
m ATTENTION!
Always make sure the device is fully assembled
before commissioning!
Installing the clip bolts (Fig. 2 - 3)
• Remove the transport lock screws (Fig. 2).
• Turn the nuts (4) over the entire length of the clip
bolts (3).
• Screw the clip bolts (3) into the threaded holes and
lock the nuts (4) against the top part of the housing
(Fig. 2).
• Drill holes into the ceiling and mount the four ceiling
mount clip bolts provided into the ceiling.
• Now hang the device onto the installation fastening
hooks using the chains provided (Fig. 3).

Scheppach HDA-14 Specifications

General

Brand	Scheppach
Model	HDA-14
Category	Water Filtration Systems
Language	English