Scheppach HM80L User Manual

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
GB
|
25
operation of machines of the same type must be ob-
served.
We accept no liability for damage or accidents which
arise due to non-observance of these instructions and
the safety information.
2. Device description (g. 1-13)
1. ON/OFF switch
2. Lock switch
3. Handle
4. Machine head
5. Moving saw blade guard
6. Saw blade
7. Set screw for rotary table
8. Stop rail
8a. Movable stop rail
8b. Set screw
9. Fixed saw table
10. Table insert
11. Scale
12. Pointer
13. Rotary table
14. Set screw for workpiece support
15. Clamping device (workpiece clamp)
16. Set screw
17. Sawdust bag
18. Workpiece support
19. Set screw for clamping device
20. Set screw for drag guide
21. Support stand
22. Adjusting screw (45°)
23. Locking screw
24. Screw for cutting depth limiting
25. Stop for cutting depth limiting
26. Adjusting screw (90°)
27. Scale
28. Pointer
29. Flange screw
30. Outer ange
31. Guide bracket
32. Saw shaft lock
33. ON/OFF switch laser
34. Battery cover
35. Laser
36. Screw
37. Transport handle
38. Clamping handle
Underframe (g. 16-19)
1. Lower leg
2. Upper leg
3. Long cross strut
4. Long connection strut
5. Short cross strut
6. Short connection strut
7. Rubber foot
8. Hexagon head screw M8x45
1. Introduction
MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
we hope your new tool brings you much enjoyment
and success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by the
product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specied,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regulations
and VDE regulations 0100, DIN 57113 / VDE0113.
We recommend:
Read through the complete text in the operating in-
structions before installing and commissioning the
device.
The operating instructions are intended to help the
user to become familiar with the machine and take ad-
vantage of its application possibilities in accordance
with the recommendations.
The operating instructions contain important informa-
tion on how to operate the machine safely, profession-
ally and economically, how to avoid danger, costly
repairs, reduce downtimes and how to increase relia-
bility and service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in
your country.
Keep the operating instructions package with the
machine at all times and store it in a plastic cover to
protect it from dirt and moisture. Read the instruction
manual each time before operating the machine and
carefully follow its information.
The machine can only be operated by persons who
were instructed concerning the operation of the ma-
chine and who are informed about the associated
dangers. The minimum age requirement must be
complied with.
In addition to the safety instructions contained in this
operating manual and the specic regulations of your
country, the technical rules generally accepted for the

Scheppach HM80L Specifications

General

Input power	1500 W
Power source	AC
AC input voltage	220-240 V
AC input frequency	50 Hz
Blade bore	30 mm
Blade diameter	210 mm
Blade thickness	2.6 mm
Idle speed (max)	5000 RPM

Weight and Dimensions

Depth	650 mm
Width	420 mm
Height	460 mm
Weight	7540 g