EasyManuals Logo

Scheppach MS132-42 User Manual

Scheppach MS132-42
Go to English
120 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #28 background imageLoading...
Page #28 background image
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
28
|
GB
Vibration A
hv
(left/right) = 8,125 m/s
2

PA
= 1,5 m/s
2
Reduce noise generation and vibration to a minimum!



Do not overload the equipment.

󰀨
Wear gloves.
When using the petrol lawn mower for extended peri-
-

We cannot give exact details about the duration of
󰀨-
vidual.


Low outside temperatures
Extended periods of use

and take regular breaks.
7. Before rst use
Assembling the components
Some parts of the mower come disassembled. For
-
tions below.
Important! You will need the following additional tools

work:

󰀩-
erating hours)

Household wipes (to wipe up oil/petrol residue; dis-

A petrol suction pump (plastic, available from DIY
stores)
An oil can with hand pump (available from DIY
stores)
Spark plug wrench
0,5 liter of engine oil (SAE 30)
Assembly
1. Take the mower and attachment parts out of the
packaging and check that all parts are present.
2. Attach the lower push bar (4a) to both sides of
the mower with one screw (a), one washer (b) and
one star grip nut (5) each. Make sure that the ca-
bles, which will be attached later, are not in the

3. Attach the upper push bar (4) on the lower push
bar (4a) with one screw (a), one washer (b) and
one star grip nut (5) each on both sides (Fig. 4-5).
4. Insert the pull start handle (17) in the designated
hook as shown in Fig. 6.
5. Fix the cables to the push bar with the cable clips
(18) provided (Fig. 7).
6. Grass box (16) - open it up and click the plastic
clips into position on the frame (Fig. 8).
7. Mowing with grass box:
        
hang the grass box (16) as shown in Fig. 9.
8. Mulching:
If the grass box (16) is attached, remove it and
replace it with the mulch insert (19) as shown in
Fig. 10-12.
Setting the cutting height
m CAUTION!
Adjust the cutting height only when the engine is
switched o󰀨 and the plug boot has been pulled.

blade is not blunt and that none of the fasteners are
damaged.
      
        
󰀨
pull the spark plug boot.
-
󰀨-
ent cutting heights can be selected.
      
cutting height. The lever snaps into the desired po-
sition. (Fig. 13)
8. Operation
m CAUTION!
The engine does not come with oil in it. There-
fore, ensure that you add 0,45 liters of oil before
starting it up. Use normal, multigrade oil (SAE30).
The oil level in the engine must be checked each
time before mowing.
You will also need to ll in petrol, as this is also
not supplied upon delivery.

lawn mower, it comes equipped with an engine
brake (Fig. 1/ Item 3) which must be pulled back
before the engine can be started. When the engine
control lever is released it must return to its initial
      
󰀨
Press the engine brake lever (3) together and give
the starter cord (17) a vigorous pull. (Fig. 14)
-
ting blade rotates even when dissolved motor brake
lever.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Scheppach MS132-42 and is the answer not in the manual?

Scheppach MS132-42 Specifications

General IconGeneral
BrandScheppach
ModelMS132-42
CategoryLawn Mower
LanguageEnglish

Related product manuals