What to do if Schumacher Electric SC1400 Battery Charger won't turn on?
If your Schumacher Electric Battery Charger isn't turning on when properly connected, the issue could stem from a dead AC outlet, a poor electrical connection, or a defective battery. First, check the AC outlet's fuse or circuit breaker. Then, inspect the power cord and any extension cords for loose connections. Finally, have the battery checked by a professional.
What does F04 mean on Schumacher Electric SC1400 Battery Charger and how to fix it?
If your Schumacher Electric Battery Charger displays error code F04, it indicates that the battery is connected backwards. To resolve this, unplug the charger and reverse the connections to the battery.
What does 'bAd bAT F05' mean on Schumacher Electric SC1400 Battery Charger and what to do?
The 'bAd bAT F05' error on your Schumacher Electric Battery Charger indicates that the battery won’t hold a charge. This may be due to a drain on the battery or a bad battery. Ensure there are no loads on the battery; if there are, remove them. If there are no loads, have the battery checked or replaced.
What does 'bAd / bAt / F05' mean on Schumacher Electric Battery Charger display?
If your Schumacher Electric Battery Charger display shows “bAD / bAt / F05”, it means lack of progress was detected after 12 hours in Maintain mode. Make sure there are no loads on the battery. If there are remove them. If there are none, have the battery checked or replaced.
What does F03 mean on Schumacher Electric Battery Charger?
The F03 error code on your Schumacher Electric Battery Charger may occur if you're trying to charge a large battery or bank of batteries on too low of a current setting. Try again with a higher current setting, or have the battery checked or replaced.
Why does my Schumacher Electric SC1400 show 'bAd / bAt / F01'?
If the display on your Schumacher Electric Battery Charger shows “bAD / bAt / F01”, it means the battery voltage is still below 10V (for a 12V battery) or 5V (for a 6V battery) after 2 hours of charging. Ensure there are no loads on the battery. If there are, remove them. If there are none, have the battery checked or replaced.
What does 'bAd bAT F02' mean on Schumacher Electric SC1400?
The error 'bAd bAT F02' on your Schumacher Electric Battery Charger indicates that the battery could not be desulfated. It is recommended to have it checked or replaced.
What does the error 'bAd / bAt / F02' mean on Schumacher Electric SC1400?
If the display on your Schumacher Electric Battery Charger shows “bAD / bAt / F02”, it means desulfation was unsuccessful, after 10 hours. Have battery checked or replaced.
What does 'bAd bAT F01' mean on Schumacher Electric SC1400?
The 'bAd bAT F01' error on your Schumacher Electric Battery Charger indicates that the battery could be bad. Have it checked or replaced.
What does SUL mean on Schumacher Electric SC1400 Battery Charger?
If your Schumacher Electric Battery Charger displays “SUL”, the charger will go into desulfation mode. If the desulfation is not successful after 10 hours, the charger will go into abort mode.
Details the dangers of explosive gases generated by batteries during operation and the importance of following instructions.
Guidelines and recommendations for using an extension cord with the battery charger.
Instructions for using the Boost or Charge/Maintain modes for charging batteries.
Provides estimated charging times for various battery sizes and applications.
Procedure for using the charger to jump-start a vehicle's engine.
General| Input Voltage | 120V AC |
|---|---|
| Output Voltage | 6V/12V |
| Weight | 4.5 lbs |
| Dimensions | 11.13" x 7.75" x 6.13" |
| LED Indicator | Yes |
| Charging Amperage | 2A, 10A, 15A |
| LCD Display | No |
| Reverse Hook-Up Protection | Yes |
| Overcharge Protection | Yes |
| Type | Battery Charger |
| Battery Type | AGM, Gel |
| Cable Length | 6 ft |
| Output Amperage | 15A |
To Next Page