Need help?Do you have a question about the Scotsman N0622 and is the answer not in the manual?
Specifies acceptable ambient air temperature ranges for the ice maker and remote condenser.
Details the acceptable range for water supply temperature for ice making.
Outlines the required minimum and maximum water pressure for the unit.
Lists the acceptable voltage ranges for the ice machine's operation.
Discusses water quality impact, recommends filtration, and specifies conductivity for RO water.
Advises on avoiding locations that could lead to contamination.
Refers to a separate document for warranty coverage details.
Discusses optimal placement, avoiding hot/dusty areas, and airflow requirements.
Mentions available kits for airflow and ice level control.
Details compatible bins, adapters, and dispenser compatibility for nugget ice models.
Provides detailed dimensional drawings of the N0422, F0522, N0622, F0822 models.
Presents dimensional diagrams for the N0922, F1222, N1322, F1522 models.
Instructions for unpacking the machine and removing panels for access.
Steps for positioning the machine on a bin or adapter and securing it.
Details how to change the bezel for the control panel switches.
Details potable water connection, backflow prevention, and drain fittings for air/water cooled models.
Instructions for connecting potable water supply and water-cooled condenser inlet.
Covers power cord, junction box, wiring, and provides a table of electrical specs and fuse sizes.
Explains connecting the remote condenser fan and coil, and lists pre-charged tubing kit numbers.
Table showing compatible condenser models for specific ice machine models and voltages.
Warns against contaminated coils and specifies headmaster requirement for remote systems.
Specifies maximum rise, drop, and line set length for remote condensers.
Provides formulas and examples for calculating total line set length.
Advises on placing the condenser near the machine with adequate space for air and cleaning.
Details requirements for roof penetrations and securing the condenser per building codes.
Describes pre-charged tubing lines, liquid/discharge lines, and quick connect couplings.
Instructions on hole sizes, routing refrigerant lines, and handling excess tubing.
Steps for preparing couplings: removing caps, cleaning, and lubricating.
Detailed procedure for tightening couplings by hand and with wrenches, including critical steps.
Final step to check all connections for leaks after opening the receiver outlet valve.
Details potable water connection, backflow prevention, and drain fittings for remote models.
Instructions for connecting potable water supply and recommends water filtration.
Steps to perform after connections, including bin preparation and electrical warm-up.
A series of questions to verify proper installation before operation.
Describes how the ice machine operates automatically once started.
Explains the function of the power, status, water, and de-scale lights.
Step-by-step instructions for powering on and starting the ice machine for the first time.
Lists the five main types of maintenance: air filters, scale removal, sanitization, sensor cleaning, and bearing checks.
Provides recommended frequencies for air filters, scale removal, sanitization, sensor cleaning, and bearing checks.
Instructions for removing, washing, and replacing air filters.
Advises on cleaning air-cooled and remote condenser fins, potentially requiring a technician.
Guidance on cleaning stainless steel exterior panels.
Instructions for checking and replacing water filter cartridges.
Detailed steps for removing scale using a specific cleaning solution.
Steps for sanitizing the water system using an approved sanitizing solution.
Instructions for inspecting the top bearing for grease condition and wear.
Advises checking the drip pan for water seal leaks during bearing checks.
Instructions for adding grease to the bearing using specific tools and cartridges.
Procedure to adjust the interval for the de-scale reminder light.
Instructions for cleaning the photo-electric eye sensors for bin level detection.
Steps for cleaning the water level sensing probe.
Describes the optional adjustable ice level control for nugget ice machines.
Details the optional Advanced Feature Board for enhanced control and logging.
Describes the add-on for remote on-off control of the machine.
Describes normal ice making, heat generation, and noise levels.
Lists common causes for the machine shutting down automatically.
Initial checks for common issues like water supply or power interruptions.
Procedure for resetting the machine after a shutdown.
Explains the meaning of various indicator light combinations for diagnostics.
General| Ice Type | Nugget |
|---|---|
| Condenser Type | Air Cooled |
| Weight | 160 lb |
| Power Supply | 115/60/1 |
| Refrigerant | R404A |
| Voltage | 115V |
To Next Page
