SDCEM MR41E - Meaning of Leds

PAGE
09
NTI010hA
CHARACTERISTICS
Operating mechanism
type MR41E
MEANING OF LEDS
Operating
mechanism status
indicators by leds
1
2
3
4
5
6
7
8
9
10
Fault indicators
by leds
off
Q
Quick
on
S
Slow
blinking FB Fast Blinking (1 flash every 4 s)
Power
Autotest
Closed
Open
Interlock
Maintenance
Heating
Other
Overload
Time Out
Status Comments
LED operating test
On card start-up, or place the selector in position
Out of Use and press
I button
Q
Communication with the PC Only with use of S-OFT (option)
FB
Board powered Fast blinking : le board is powered
Autotest OK
Auto-test failed on boot
Auto-test failed in operation
Blocking fault
blinks alternately. To clear the fault, place the selector in LOCAL mode
or switch off the board.
Limit stop not reached
Limit stop in position
Limit stop not reached
Limit stop in position
Limit stop problem or Fault of one (or +)
position(s) of the group (master LAN) in
PNT mode
blinks alternately. To clear the fault, place the selector in MANUAL
mode, then place in initial position or switch off the board.
Interlock disabled The operating mechanism can not be operated
S
Interlock opened during movement
S
Trigger loss during movement
Interlock enabled The operating mechanism can be operated
No maintenance required
Maintenance required
To clear after maintenance, place the selector in MANUAL mode and
press the buttons O and I at the same time
No fault
Fault present
To clear the fault, place the selector in MANUAL mode, then place in
initial position
No fault
Fault present
To clear the fault, place the selector in MANUAL mode, then place in
initial position
No fault
Fault present
To clear the fault, place the selector in MANUAL mode, then place in
initial position
No fault
Fault present
To clear the fault, place the selector in MANUAL mode, then place in
initial position
Key to symbols
Status Default
To reboot, switch off the board
To clear the fault, place the selector in MANUAL mode, then place in
initial position
off Q Quick
on
S
Slow
blinking FB Fast Blinking (1 flash every 4 s)
Power
Autotest
Closed
Open
Interlock
Maintenance
Heating
Other
Overload
Time Out
Status Comments
LED operating test
On card start-up, or place the selector in position Out of Use and press
I button
Q
Communication with the PC Only with use of S-OFT (option)
FB
Board powered Fast blinking : le board is powered
Autotest OK
Auto-test failed on boot
Auto-test failed in operation
Blocking fault
blinks alternately. To clear the fault, place the selector in LOCAL mode
or switch off the board.
Limit stop not reached
Limit stop in position
Limit stop not reached
Limit stop in position
Limit stop problem or Fault of one (or +)
position(s) of the group (master LAN) in
PNT mode
blinks alternately. To clear the fault, place the selector in MANUAL
mode, then place in initial position or switch off the board.
Interlock disabled The operating mechanism can not be operated
S
Interlock opened during movement
S
Trigger loss during movement
Interlock enabled The operating mechanism can be operated
No maintenance required
Maintenance required
To clear after maintenance, place the selector in MANUAL mode and
press the buttons O and I at the same time
No fault
Fault present
To clear the fault, place the selector in MANUAL mode, then place in
initial position
No fault
Fault present
To clear the fault, place the selector in MANUAL mode, then place in
initial position
No fault
Fault present
To clear the fault, place the selector in MANUAL mode, then place in
initial position
No fault
Fault present
To clear the fault, place the selector in MANUAL mode, then place in
initial position
Key to symbols
Status Default
To reboot, switch off the board
To clear the fault, place the selector in MANUAL mode, then place in
initial position