Sealey SCSG04 User Manual

INSTRUCTIONS FOR
PREMIUM PRESSURE SOLVENT SPRAYER
WITH VITON SEALS 1LTR
MODEL NO: SCSG04
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
 WARNING! Wear approved eye protection. Wear appropriate Personal Protective Equipment. A full range of Personal Protective
Equipment is available from your Sealey dealer.
 WARNING! Ensure that Health & Safety, Local Authority Regulations and general workshop practice Regulations are adhered to
when using sprayer.
9 Be aware of the safety requirements for the fluids contained in the vessel.
9 Do read and follow all the fluid manufacturers instructions for application and safe use.
9 Store the sprayer out of reach of children.
9 Label vessel with chemical used, even if water. It is highly recommended that individual vessels should be used for individual
chemicals. Cross contamination can give unexpected results.
8 DO NOT spray at people, animals, in high winds, or where there are sources of ignition.
8 DO NOT use the pressure sprayer for any purpose other than for which it is designed.
8 DO NOT use whilst eating, drinking, smoking; under the influence of drugs, alcohol, intoxicating medication, or if fatigued.
8 DO NOT leave the tank pressurised for long periods of time.
8 DO NOT expose the sprayer to direct sunlight.
8 DO NOT fill the container with liquids exceeding 30°C.
2. INTRODUCTION
Premium quality hand pump sprayer. Ideal for use with some brake cleaners, detergents, traffic film removers, penetrating oils and weed killers.
Adjustable nozzle enables a mist to jet pattern, which allows for easy and direct application of liquid exactly where it is required. Robust composite
construction with a 1ltr capacity container.
SCSG04 | Issue 1 02/02/16
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Wear eye
protection
Wear a mask

Sealey SCSG04 Specifications

General

Model No	SCSG04
Air Consumption	4-6 CFM
Cup Capacity	600ml
Weight	1.2 kg
Air Inlet	1/4 inch BSP
Type	Gravity Feed

Summary

Safety Precautions

General Safety and PPE

Wear approved eye protection and appropriate Personal Protective Equipment for safe operation.

Adherence to Regulations

Ensure adherence to Health & Safety, Local Authority, and general workshop practice regulations.

Fluid Safety and Instructions

Be aware of fluid safety requirements and follow all fluid manufacturer instructions for safe use.

Child Safety

Store the sprayer out of reach of children to prevent accidental use.

Vessel Labeling and Cross-Contamination

Label vessels with chemicals used and use individual vessels to prevent cross-contamination.

Operational Prohibitions

Avoid spraying people, animals, high winds, ignition sources, misuse, and improper storage or temperature.

Product Introduction

Product Overview

Description of the premium quality hand pump sprayer, its uses, and features.

Preparation and Setup

Pre-Use Inspection

Check all parts are undamaged and working correctly before using the sprayer.

Tank Preparation

Unscrew the pump from the tank for filling and preparation.

Filling Procedure

Fill the canister up to the designated 'max' level with the desired liquid.

Sealing the Sprayer

Screw the pump head on tightly to ensure the canister is sealed and airtight for pressure build-up.

Operation Guide

Pressurizing the Tank

Pump air into the tank (20-30 movements) using the piston to build pressure.

Spray Pattern Adjustment

Press the spray button and adjust the spray nut for desired mist to jet pattern.

Air Escape Procedure

Spray upwards at an incline to release residual air if liquid drips after button release.

Fluid Compatibility

Ensure use of clean spray agents and mix chemicals thoroughly prior to filling.

Post-Operation Procedures

Slowly unscrew spray head to release pressure, clean pump with water or agent.

Maintenance and Care

Routine Maintenance

Oil the pump piston occasionally and check nozzle/filter for deposits.

Replacement Parts

A kit of new seals is available from your Sealey dealer (Part No. SCSGPRK).