Seastar Solutions Hynautic 04 Series - Clutch Slave Installation

6
Hynautic Hydraulic Engine Controls – 04 Series
/iÊ-i>-Ì>ÀÊ-ÕÌÃÊVÕÌVÊÃ>ÛiÊÕÃÌÊLiÊÕÌi`ÊÃÊÌ>ÌÊÜiÊÌiÊ
i}i½ÃÊÌÀ>ÃÃÃÊÃÊÊiÕÌÀ>Ê>`ÊÌiÊÀÃiÊVÕÌVÊÃ>Ûi½ÃÊ>ÀÊÃÊ
>ÌÊÌÃÊ`ÃÌÀi]ÊLÌÊ>ÀÃÊÜÊLi\Ê£®ÊÊÌiÊÃ>iÊ«>iÆÊӮʫ>À>iÊÌÊ
i>VÊÌiÀÆÊ>`ÊήÊÀ}ÌÊ>}iÃÊÜÊLiÊvÀi`ÊLiÌÜiiÊViVÌ}Ê
>}iÊ>`Êi>VÊ>À]ÊÃiiÊ}ÕÀiÊÇ°
Clutch Slave Installation
BALL JOINT
(670010)
BALL JOINT
(670010)
LOCK NUT
LOCK NUT
SLAVE ARM
CLUTCH ARM
1/4-20
THREADED
ROD
90˚
90˚
Figure 7. Proper Clutch Slave to Throttle Arm Installation.
NOTICE
The clutch slave’s arm may be set to any desired position by
loosening the tightening screw (using a 3/16" allen wrench) in the
lower end of the arm. Rotate arm as desired and reset the screw.
After the arm is set it will have a 78° maximum arc.
1Ê -iVÕÀiÊÕÌ}ÊLÀ>ViÌÊÌÊÌiÊi}i°ÊÊÃÕÌ>LiÊLÀ>ViÌÊÕÃÌÊ
LiÊv>LÀV>Ìi`°
2Ê -iVÕÀiÊÌiÊÌÀ>ÃÃÃÊÃ>ÛiÊÌÊÌiÊÕÌ}ÊLÀ>ViÌÊÕÃ}ÊÌiÊ
ÎÉn£ÈÊÕÌ}ÊLÌð
3Ê -iÌÊÌiÊÌÀ>ÃÃÃÊÊÌiÊiÕÌÀ>Ê«ÃÌ]Ê>`ÊÌiÊVÕÌVÊ
Ã>Ûi½ÃÊ>ÀÊ>ÌÊÌÃÊ`ÃÌÀi°
4Ê ÃiÊÌiÊÃiÌÊÃVÀiÜÊÊÌiÊ`iÌiÌÊÀ}ÊÊÌiÊVÕÌVÊÃ>ÛiÊ>`Ê
ÀÌ>ÌiÊÌiÊ`iÌiÌÊÀ}ÊÌÊÌiÊvÕÊ`iÌiÌÊ«ÃÌ°Ê/ÊV>ÌiÊÌiÊ
`iÌiÌÊÀ}]ÊÃiiÊ}ÕÀiÊn°
5Ê -iVÕÀiÊ`iÌiÌÊÀ}ÊÊÌÃÊ«ÃÌÊLÞÊÌ}Ìi}ÊÌiÊÃiÌÊÃVÀiÜ°
6Ê ÃÌ>Ê>ÊVÊÕÌÊ>`ÊL>ÊÌÊÊÌiÊi`ÊvÊÌiÊ£É{ÓäÊÃÌ>iÃÃÊ
ÃÌiiÊÀÊLÀ>ÃÃÊÌÀi>`i`ÊÀ`ÊÌÊ«ÀÛ`i`®°
7Ê *ÃÌÊÌiÊVÕÌVÊÃ>ÛiÊÌÊÌÃÊ`ÃÌÀiÊ>`ÊViVÌÊÌiÊL>Ê
ÌÊi`ÊvÊÌiÊ£É{ÓäÊÌÀi>`i`ÊÀ`ÊÌÊÌ°
8Ê *ÃÌÊÌiÊi}i½ÃÊVÕÌVÊ>ÀÊÌÊiÕÌÀ>]Ê`iÌiÀiÊÌiÊ«À«iÀÊ
i}ÌÊvÊÌiÊÌÀi>`i`ÊÀ`ÊÀiµÕÀi`Ê>`ÊVÕÌÊvvÊÌiÊiÝViÃð
9Ê ÃÌ>Ê>ÊVÊÕÌÊ>`ÊL>ÊÌÊÊÌiÊÌiÀÊi`ÊvÊÌiÊÌÀi>`i`ÊÀ`°
COMPONENT INSTALLATION
HYNAUTIC CONTROLS