Seko PoolBasic EVO User Manual

0000136864 rev. 4.2
1
POOL BASIC evo
WARNINGS
! IMPORTANT!
Before carrying out ANY work inside control panel of the Pool Basic Evo device, make sure you disconnect it
from the power supply.
FAILURE TO COMPLY WITH THE INSTRUCTIONS CONTAINED IN THIS MANUAL COULD CAUSE INJURY TO
PEOPLE AND/OR DAMAGE TO THE APPLIANCE AND THE SYSTEM.
PACK CONTENTS
A) "Pool Basic" pH control device (standard model)
B) PVC Cristal 4x6 suction hose (4 m)
C) Polyethylene delivery hose (5 m)
D) Attachment screw (φ=6 mm)
E) Foot filter (PVC riser)
F) FPM duckbill valve (3/8” GAS)
G) SPH-1 pH electrode
H) PSS3 probe-socket (1/2” GAS)
I) Tapping saddle for securing PSS3 onto 2” hose
(φ=50 mm)
L) pH 4, pH 7, H
2
O buffer solution kit
M) Reducer for injection valve
The pH probe is a product subject to wear and tear and is therefore not covered by the warranty.
 Chemical products:
Recommended for lowering pH => negative pH (with a sulphuric acid base)
Recommended for raising pH => positive pH (sodium carbonate or bicarbonate)
ABSOLUTELY not recommended => pure sulphuric acid
Note: These products are DANGEROUS (IA) and require special precautions during use, handling and storage.
 Pool Basic Evo was designed to regulate the pH of tanks up to 90 m
3
.
B NEVER mix chemical products.
B NEVER allow children or people who have not read this manual to use or tamper with Pool Basic Evo or any of
its peripheral components (including chemical products).
TECHNICAL SPECIFICATIONS
Dimensions (H – W – L) 234x162x108 mm Maximum back-pressure 1,5 bar
Weight 1 kg Pump state Pause - Supply
Power supply 50 Hz 230 VAC pH scale 6.2 pH – 8.0 pH
Consumption 7 W o 12,5 W pH control range 0.0 pH – 14.0 pH
Pump flow rate 1,5 l/h; 5 l/h Device precision +/- 0.02 pH
Electrode regulation Automatic
Wall Mounting Setup
Make sure that the injection pressure is below 1.5 bar.

Seko PoolBasic EVO Specifications

General

Brand	Seko
Model	PoolBasic EVO
Category	Lighting Equipment
Language	English

Summary

Pack Contents

Technical Specifications

Wall Mounting Setup

Positioning the Probe

Electrical Wiring

Set Point Adjustment

Adjustment (Setup)

Enter Setup Programme

Press and hold Enter and Esc keys for 5 seconds to access the setup programme.

Acid Dosing Setup

Configure the device to dose acid products for negative pH adjustment.

Alkaline Dosing Setup

Configure the device to dose alkaline products for positive pH adjustment.

Calibration Control

Block or authorize the calibration function using the Enter key.

OFA Alarm Control

Block or authorize the Overdose Alarm (OFA) function using the Enter key.

Flow Function Control

Block or authorize the Flow function using the Enter key.

Easy Cal Function Control

Block or authorize the Easy Cal function using the Enter key.

Exit Setup Menu

Confirm and exit the setup menu by pressing the Esc key.

Probe Calibration

Initial Rinse and Buffer

Rinse the probe with H2O, then place it in the 7 pH buffer solution.

7 pH Calibration

Press the Cal key for 5 seconds to initiate the 7 pH calibration.

Calibration Wait Period

Please wait during calibration for 1 minute after the initial 7 pH step.

Second Buffer Solution

Rinse probe with H2O, then place it into the 4 pH buffer solution.

4 pH Calibration

Press Enter key to calibrate the second point (4 pH buffer solution).

Save and Exit Calibration

Press Enter key to save the calibration settings and exit the process.

The Pump

The Probe Handling

Alarms and Troubleshooting

OFA (Overdose Alarm)

Details on First and Second OFA alarms, their triggers, and resolution steps.

Flow Alarm

Indicates presence of incoming flow, enslaved by the filter pump.

Alarm Codes and Actions

Table of alarms, LEDs, relays, and required actions for system errors.

Restore Default Parameters

Steps to restore default settings by powering off, pressing keys, and powering on.