What to do if SeQual Eclipse 1000 shows 'UNIT NEEDS ATTENTION - Flow Rate Error/ Blocked Flow'?
If your SeQual Oxygen Equipment displays a 'Flow Rate Error/ Blocked Flow' message, inspect the tubing and/or humidifier for any obstructions. Also, check and clean the air intake filter. If the condition continues for more than 10 minutes, contact your dealer/provider.
What to do if SeQual Oxygen Equipment shows 'UNIT NEEDS ATTENTION - O2 Concentration < 85%'?
If your SeQual Oxygen Equipment displays an 'O2 Concentration < 85%' message, continue use and check or clean the air intake filter. If the condition persists, contact your dealer/provider.
What to do if SeQual Eclipse 1000 Oxygen Equipment shows 'UNIT NEEDS ATTENTION - O Concentration < 70%'?
If your SeQual Oxygen Equipment displays an 'O Concentration < 70%' message, continue use and check or clean the air intake filter. If the condition persists, contact your dealer/provider.
Why is my SeQual Oxygen Equipment not turning on?
Your SeQual Oxygen Equipment might not be turning on for several reasons. Ensure a charged Power Cartridge is installed or plug the unit into an external power source. If the Power Cartridge is discharged, plug into external power. If the issue persists, there may be a malfunction, and you should contact your dealer/provider.
What to do if my SeQual Eclipse 1000 has no oxygen?
If your SeQual Oxygen Equipment isn't delivering oxygen, first check the tubing for any blockages or kinks and replace if necessary. Ensure the air inlet filter is clean. Inspect the humidifier attachment and tubing. Make sure the device is turned on. Check that the tubing, cannula, and connections are properly connected and not kinked. Install a charged Power Cartridge or connect to an external power source. If none of these steps resolve the issue, contact your dealer/provider.
What to do if my SeQual Eclipse 1000 has shutdown due to loss of external power?
If your SeQual Oxygen Equipment shuts down due to a loss of external power and you don't have a charged Power Cartridge installed, use an alternative oxygen supply until the external power is restored or install a charged Power Cartridge.
What to do if my SeQual Oxygen Equipment has low oxygen concentration?
If your SeQual Oxygen Equipment is showing a low oxygen concentration, check for any restrictions in the tubing or humidifier and repair or replace if needed. Also, inspect the air inlet filter and clean or replace it if it's restricted. If the problem persists, contact your dealer/provider.
Why is there no oxygen delivered in pulse mode on my SeQual Eclipse 1000 Oxygen Equipment?
If your SeQual Oxygen Equipment isn't delivering oxygen in Pulse Mode, ensure the tubing/cannula is no longer than 7 feet (2.1m). Remove any humidifier attached. If the issue persists, contact your dealer/provider.
What does 'UNIT NEEDS ATTENTION - Low or Warm Power Cartridge' mean for SeQual Eclipse 1000 Oxygen Equipment?
If your SeQual Oxygen Equipment displays 'UNIT NEEDS ATTENTION - Low or Warm Power Cartridge', plug the unit into external power or replace the current cartridge with a charged one.
What to do if my SeQual Oxygen Equipment has low oxygen flow?
If your SeQual Oxygen Equipment has a low oxygen flow, check for any restrictions in the humidifier or tubing and repair or replace them as needed. Also, inspect the air inlet filter and clean or replace it if it's blocked. If the problem continues, contact your dealer/provider.
Explains symbols and warnings used in the manual and on the oxygen system.
Lists conditions or situations where the ECLIPSE system should not be used.
Provides critical safety information regarding oxygen therapy.
Details safe practices for operating the ECLIPSE oxygen system.
Outlines safety precautions related to the power cartridge.
Identifies key features and components of the ECLIPSE oxygen system.
Explains the icons, numbers, and indicators on the control panel.
Describes the function of the control buttons and indicators.
Details the meaning of the green, yellow, and red indicators on the panel.
Advises on selecting an appropriate location for the ECLIPSE system.
Provides initial steps and important information before operating the system.
Explains how to power the ECLIPSE system using different sources.
Guides the user through the steps of using the ECLIPSE system.
Outlines routine maintenance tasks performed by technicians and users.
Provides instructions for cleaning and caring for the system by the patient.
General| AC Power | 100-240 VAC, 50/60 Hz |
|---|---|
| Operating Temperature | 41°F to 104°F (5°C to 40°C) |
| Operating Humidity | 10% to 95% non-condensing |
| Battery Life | Up to 5 hours |
| Pulse Dose Settings | 1 to 6 |
| DC Power | 12 VDC |
| Operating Altitude | Up to 10, 000 feet (3, 048 meters) |
| Power Requirements | 100-240 VAC, 50/60 Hz |
To Next Page
