Sharp 8M-B32C1 User Manual

20
E
Menu Items
n
EXTENSION (HDMI1/HDMI2)
LUMINANCE CLIPPING*
1
*
2
Clips area with luminance higher than the one specified in CLIP LUMINANCE according to the input HDR signal.
When PQ signal is input ............ Can be selected from OFF, ON, or TONE-MAPPING.
In addition, luminance can be configured from CLIP LUMINANCE. According to the setting,
video display is adjusted as follows.
OFF ON TONE-MAPPING
Displays up to 600 cd/m
2
following the
PQ curve.
Area with luminance higher than the
one set in CLIP LUMINANCE will be
clipped and displayed.
Displays to avoid excessive change
near the luminance set in CLIP
LUMINANCE.
064 256 512
1023
0
200
400
600
800
1000
1200
(cd/m
2
)
Input tone
PQ (SMPTE ST2084) Monitor display
Set luminance
(600cd/m
2
)
LUMINANCE
(cd/m
2
)
064 256 512 1023
0
200
400
600
800
1000
1200
Input tone
Set luminance
(600cd/m
2
)
CLIP LUMINANCE
(1000cd/m
2
)
PQ (SMPTE ST2084) Monitor display
LUMINANCE
064 512256
1023
PQ (SMPTE ST2084) Monitor display
0
200
400
600
800
1000
1200
Input tone
Set luminance
(600cd/m
2
)
CLIP LUMINANCE
(1000cd/m
2
)
(cd/m
2
)
LUMINANCE
When HLG signal is input .......... Can be selected from OFF or ON. According to the setting, video display is adjusted as follows.
OFF ON
Lowers the overall luminance and displays
so that the luminance of video is wholly
below the set luminance of the monitor.
Area higher than 600 cd/m
2
will be
clipped and displayed.
0
200
400
600
800
1000
Input tone
HLG (Hybrid Log Gamma) Peak1000 cd/m
2
Monitor display
Set luminance
(600cd/m
2
)
(cd/m
2
)
064 256 512
1023
LUMINANCE
HLG (Hybrid Log Gamma) Peak1000 cd/m
2
Monitor display
0
200
400
600
800
1000
Input tone
Set luminance
(
600cd/m
2
)
064 256 512
1023
(cd/m
2
)
LUMINANCE
ON, OFF, and TONE-MAPPING of LUMINANCE CLIPPING can be configured in the following cases:
• When COLOR MODE is BT.2100(PQ) or HDR AUTO(PQ).
• When COLOR MODE is USER1 or USER2, CUSTOM SETTING is OFF, COLOR GAMUT is Rec.2020, and GAMMA(EOTF)
is SMPTE ST 2084(PQ).
• When COLOR MODE is USER1 or USER2, CUSTOM SETTING is ON, Color gamut*
3
is Rec.2020*
3
, Gamma*
3
is PQ*
3
,
and LUT (.cube file)*
3
is not specified.
OFF and ON of LUMINANCE CLIPPING can be configured in the following cases:
• When COLOR MODE is BT.2100(HLG) or HDR AUTO(HLG).
• When COLOR MODE is USER1 or USER2, CUSTOM SETTING is OFF, COLOR GAMUT is Rec.2020, and GAMMA(EOTF)
is HYBRID LOG GAMMA(HLG).
• When COLOR MODE is USER1 or USER2, CUSTOM SETTING is ON, Color gamut*
3
is Rec.2020*
3
, Gamma*
3
is HLG*
3
,
and LUT (.cube file)*
3
is not specified.
*1 These are examples with LUMINANCE set to 600 cd/m
2
. If LUMINANCE is set lower than 600 cd/m
2
, the overall
luminance will become low.
*2 Set DYNAMIC RANGE EXPAND to MODE1 or MODE2.
*3 They are setting items for Display Calibration Utility.
Caution
• For HDMI3 input and DisplayPort input, the menu is displayed but the function cannot be enabled.

Sharp 8M-B32C1 Specifications

General

Brand	Sharp
Model	8M-B32C1
Category	Monitor
Language	English