EasyManua.ls Logo

Sharp AQUOS LC-32M450M - Remote Control Unit; Part Names; TV Front and Rear Overview; Powering the TV On;Off

Sharp AQUOS LC-32M450M
8 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
5 6
Remote control unit
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
6 FREEZE
Freeze a motion picture on the screen. (See page 13.)
7 EXIT
Return to the default screen.
8 Colour (Red/Green/Yellow/Blue)
TELETEXT mode: Select a page. (See page 14.)
9 POWER (STANDBY/ON)
To switch the power on and off. (See page 6.)
10 DISPLAY
Display the channel or input information.
11 SLEEP
Set the Sleep timer.
0 hr. 30 min. 1 hr. 00 min.
2 hr. 30 min.
1 hr. 30 min.
2 hr. 00 min.
Off
12 AV MODE
Select an audio and video setting. (See page 8.)
13 MPX
Select the sound multiplex mode.
14 INPUT (INPUT SOURCE)
Select an input source.
15 CH
r
/CH
s
TV input mode: Select the channel.
(CH
r
) Increase the channel number.
(CH
s
) Decrease the channel number.
TELETEXT mode: Select the page. (See page 14.)
16 PC
Directly select the PC terminal.
17 MENU
Display the menu screen.
18
a
/
b
/
c
/
d
(Cursor)
Select a desired item on the setting screen.
ENTER
Execute a command.
19 RETURN
MENU mode: Return to the previous menu screen.
20
m
(TELETEXT),
k
(Reveal hidden for TELETEXT),
[
(SUBTITLE for TELETEXT),
3
(Hold),
1
(Subpage),
v
(Top/Bottom/Full)
Use for TELETEXT mode. (See page 14.)
1
e
(Mute)
Press
e
s
Mutes sound.
Press
e
again
s
Restores sound.
Mute will be cancelled after 30 minutes. However,
the TV will not suddenly output loud sound as the
volume level will be set to 0 automatically. Increase
the volume level by pressing VOL
k
.
2 0 – 9
Set the channel.
TELETEXT mode: Set the page. (See page 14.)
3
A
(Flashback)
Press
A
to return to the previous selected channel
or external input mode.
4 WIDE
Change the wide image mode. (See pages 13 and 14.)
5 VOL
k
/VOL
l
Set the volume.
(VOL
k
) Increase the volume.
(VOL
l
) Decrease the volume.
Inserting the battery
Before using the TV for the fi rst time, insert a “AA” size battery (supplied). When the battery become depleted
and the remote control fails to operate, replace the battery with new “AA” size battery.
1
Open the battery cover.
2
Insert the supplied “AA” size battery.
3
Close the battery cover.
Place battery with their terminals corresponding to the
(
e
) and (
f
) indications in the battery compartment.
CAUTION
• Battery (battery pack or battery installed) shall not be exposed to excessive heat such as sunshine, fi re or the like.
Part names
TV (Front)
Remote control sensor
OPC sensor
POWER indicator
Light off Power off
Lighted (Red) The TV is in standby mode.
Lighted (White) The TV is on.
TV (Rear)
9
8
7
6
10
12
13
11
14
15
1
2
3
4
5
18
16
17
1 POWER (On/Off) button
2 MENU button
3 INPUT button
4 Channel up (
r
)/down (
s
) buttons
5 Volume up (
e
)/down (
f
) buttons
6 DIGITAL AUDIO OUTPUT terminal
7 INPUT 7 (PC) terminals*
8 RS-232C terminal
9 Antenna input terminal
10 INPUT 4 terminals
11 INPUT 5 terminals
12 INPUT 6 terminals
13 AUDIO OUT terminal
14 INPUT 2 (HDMI) terminal
15 INPUT 1 (HDMI) terminal*
16 USB terminal**
17 INPUT 3 (HDMI) terminal
18 Headphone jack (
3.5 mm)
• The speakers do not output volume
when headphones are plugged in.
* The INPUT 1 and INPUT 7 terminals can both use the same audio input terminal. However, the proper item must be
selected in the “PC audio select” menu. (See page 12.)
** USB terminal use for USB Media Player. Please see “USB Media Player Operation Manual” in separate sheet.
• The illustrations in this operation manual are for explanation purposes and may vary slightly from the actual operations.
• The illustrations used throughout this manual are based on LC-40M550M.
Turning the TV on/off
Turning on/off the power Standby mode
To turn on the power
Press POWER on the TV. (After a few seconds, an image
appears with sound.)
To turn off the power
Switch it off by pressing POWER on the TV.
To standby mode
If the TV is switched on, you can switch it to standby by
pressing POWER on the remote control.
Switching on from standby
From standby, press POWER on the remote control.
NOTE
• If you are not going to use this TV for a long period of time, be sure to remove the AC cord from the AC outlet.
• Minor power is consumed when the unit is in standby mode.
LC32M450M_EN.indd 3LC32M450M_EN.indd 3 6/28/2011 4:56:35 PM6/28/2011 4:56:35 PM

Related product manuals