Useful adjustment settings
For automatically adjusting the
PC
image.
Press
MENU
to display the MENU screen, and
then press
......
/~
to select "Setup".
Ordinarily you can easily adjust the picture
as
necessary to change image position using Auto Sync.
In
some cases, however, manual adjustment
is
needed
to optimize the image.
Press
MENU
to display the MENU screen, and
then press
......
/~
to select "Setup".
Press
.l~
to select "Fine Sync.", and then
press
ENTER.
Press
.l~
to select "Auto Sync.", and then
press
ENTER.
Press
......
/~
to select "Yes", and then press
ENTER.
• Auto Sync. starts and "Now adjusting the image."
displays.
Press
MENU
to exit.
H-Pos.
V-Pas.
Clock
Phase
Press
./T
to select the specific adjustment
item.
Centers the image by moving
it
to
the left
or right.
Centers the image by moving
it
up or
down.
Adjust when the image flickers with vertical
stripes.
Adjust when characters have low contrast
or when the image flickers.
Press
......
/~
to adjust the item to your desired
position.
Press
MENU
to exit.
• When Auto Sync.
is
successful, "Completed" displays.
If
not, Auto Sync. failed.
• Auto Sync. may
fail
even
if
"Completed" displays.
• Auto Sync. may
fail
if
the computer image has low
resolution, has unclear (black) edges, or
is
moved while
executing Auto Sync.
• Be sure to connect the
PC
to the TV and switch
it
on
before starting Auto Sync.
(@-
32
• For resetting
all
Fine Sync. adjustment items to the factory
preset values, press
..
/~
to select "Reset", and then
press
ENTER.
•
It
is
not necessary to adjust the "Clock" or "Phase" when a
digital signal
is
being input, so
it
cannot be selected.
• The default cursor position may not be
in
the center,
because the screen position variable ranges may be
asymmetrical.
• The screen position variable ranges depend on the View
Mode or the signal type. The ranges can be seen on the
position-setting screen.
Useful adjustment settings
For automatically adjusting the
PC
image.
Press
MENU
to display the MENU screen, and
then press
......
/~
to select "Setup".
Ordinarily you can easily adjust the picture
as
necessary to change image position using Auto Sync.
In
some cases, however, manual adjustment
is
needed
to optimize the image.
Press
MENU
to display the MENU screen, and
then press
......
/~
to select "Setup".
Press
.l~
to select "Fine Sync.", and then
press
ENTER.
Press
.l~
to select "Auto Sync.", and then
press
ENTER.
Press
......
/~
to select "Yes", and then press
ENTER.
• Auto Sync. starts and "Now adjusting the image."
displays.
Press
MENU
to exit.
H-Pos.
V-Pas.
Clock
Phase
Press
./T
to select the specific adjustment
item.
Centers the image by moving
it
to
the left
or right.
Centers the image by moving
it
up or
down.
Adjust when the image flickers with vertical
stripes.
Adjust when characters have low contrast
or when the image flickers.
Press
......
/~
to adjust the item to your desired
position.
Press
MENU
to exit.
• When Auto Sync.
is
successful, "Completed" displays.
If
not, Auto Sync. failed.
• Auto Sync. may
fail
even
if
"Completed" displays.
• Auto Sync. may
fail
if
the computer image has low
resolution, has unclear (black) edges, or
is
moved while
executing Auto Sync.
• Be sure to connect the
PC
to the TV and switch
it
on
before starting Auto Sync.
(@-
32
• For resetting
all
Fine Sync. adjustment items to the factory
preset values, press
..
/~
to select "Reset", and then
press
ENTER.
•
It
is
not necessary to adjust the "Clock" or "Phase" when a
digital signal
is
being input, so
it
cannot be selected.
• The default cursor position may not be
in
the center,
because the screen position variable ranges may be
asymmetrical.
• The screen position variable ranges depend on the View
Mode or the signal type. The ranges can be seen on the
position-setting screen.
To Next Page
Loading...
