13
GENERAL PROGRAMS
OUTPUT TRAYS
(When the printer or fax function is enabled and a JOB
SEPARATOR TRAY KIT or FINISHER is installed)
This program is used to select the respective output
trays for the copy, printer, and fax functions.
The factory default setting is "PATTERN 1".
Example: When a FINISHER is installed
* Settings that can be selected vary depending on the
options that are installed.
OFFSET FUNCTION SETTING
This program is used to enable or disable the offset
functions of the centre tray and offset tray (when a
FINISHER is installed).
This program is initially enabled (factory default
setting).
MEMORY FOR PRINTER
This program is used to set the amount of IMC
memory that is allocated to the printer function. The
amount of memory can be set from 30% to 70% in
increments of 10%.
The factory default settings are as follows:
•50 (%)
• THE MEMORY AREA FOR PRINT HOLD: 30 (%)
● Memory allocated to print hold
(When the PRINTER EXPANSION KIT is installed)
To set the amount of memory allocated to print hold,
touch the [THE MEMORY AREA FOR PRINT
HOLD] key. The amount of memory can be set from
30% to 70% in increments of 10%. If 0% is selected,
the print hold function cannot be used.
DISABLING OF CENTRE TRAY
COUNTING
This program is used to disable counting of pages
delivered to the centre tray.
When this program is enabled, centre tray full
detection does not take place.
This program is initially disabled (factory default
setting).
RETURN FROM COPY MODE TIMING
(When the printer function or fax function is enabled)
This program is used to set the amount of time that
must elapse after a copy job is finished before the
printer or fax function resumes operation. The amount
of time can be set from 1 second to 60 seconds in
increments of 1 second.
The factory default setting is "60" (sec.).
MIX SIZE ORIGINAL FEEDING MODE
(When an RSPF is installed)
When this program is enabled, originals of mixed
length (the widths must be the same) can be scanned
in copy mode and each original copied onto the
corresponding length of paper.
This program is initially disabled (factory default
setting).
SECURITY SETTINGS
The following settings are related to security. Touch
the [SECURITY SETTINGS] key to configure the
settings.
When any of these settings are changed, you must exit
the administrator settings, turn off the main switch, wait
a brief interval, and then turn the main switch back on
to make the new settings take effect.
● SSL SETTINGS
SSL can be used for data transmission over a
network.
SSL is a protocol that enables the encryption of
information communicated over a network.
Encrypting data makes it possible to transmit and
receive sensitive information safely.
•
HTTPS: Apply SSL encryption to HTTP
communication.
•
IPP-SSL: Apply SSL encryption to IPP communication.
● ENABLE IPsec
IPsec can be used for data transmission/reception
on a network. When IPsec is used, data can be sent
and received safely without the need to configure
settings for IP packet encryption in a Web browser
or other higher-level application.
This setting is only used to enable or disable IPsec;
detailed IPsec settings are configured in the Web
pages.
Some Web page settings may not allow connection
to the machine, or the settings may not allow
printing, scanning, or Web page display. In this
case, deselect [ENABLE IPsec] in this screen and
change the Web page settings.
Settings Description
PATTERN 1 Copy: Offset tray
Printer: Centre tray
Fax: Top tray
PATTERN 2 Copy: Centre tray
Printer: Offset tray
Fax: Top tray
PATTERN 3
(When the fax
function is enabled)
Copy: Centre tray
Printer: Offset tray
Fax: Centre tray
PATTERN 4
(When the fax
function is enabled)
Copy: Offset tray
Printer: Centre tray
Fax: Centre tray
SYSTEM SETTINGS
SECURITY SETTINGS
SSL SETTINGS
ENABLE IPsec
OK
To Next Page
Loading...
