Sharp AR-M257 - Page 99

104 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

MEMO

!Andromeda_copy_sec.book 97 ページ２００６年１２月１８日　月曜日　午前９時３５分

Table of Contents

Default Chapter3
- Table of Contents3
Cautions5
- Cautions on Using the Machine5
- Important Points When Selecting an Installation Site5
- Cautions on Handling the Machine6
- Laser Information6
- Environmental Information7
- 1 Before Using the Machine5
Using the Manual7
- About the Operation Manuals7
- The Meaning of "R" in Original and Paper Size Indications8
- Conventions Used in this Manual8
Main Features9
Part Names and Functions10
- Operation Panel12
- Touch Panel13
  - Using the Touch Panel13
  - The Machine10
Power on and off15
- Power on15
- Power off15
- Initial Settings16
- Power Save Modes16
Loading Paper17
- Paper17
- Special Papers18
- Letterhead Paper18
- Loading Paper19
- Loading the Paper in the Paper Tray19
- Loading Paper in the Bypass Tray20
- Changing a Tray's Paper Type and Paper Size Settings21
- Setting the Paper Type in the Bypass Tray22
Main Screen of Copy Mode23
Normal Copying24
- Copying from the Document Glass24
- Copying from the Rspf25
- Points to Note When Making Copies26
- Originals that Can be Used in the Rspf26
- Original Size] Key27
- BYPASS FEED (Special Paper)28
Automatic Two-Sided Copying29
- Using the Document Glass29
- Copy] Key29
- Using the Rspf30
Exposure Adjustment31
- Manually Adjusting the Exposure31
Reduction/Enlargement/Zoom32
- Automatic Ratio Selection32
- Manual Ratio Selection33
- (XY ZOOM Copying)34
Interrupting a Copy Run36
Copy Finishing Functions37
- Sort Copy37
- Group Copy37
- Offset Function37
- When Using the Document Glass38
- (AR-FN5A) Is Installed)39
- Stapling Positions39
- Staple Sort39
Special Modes41
- General Procedure for Using the42
- Special Functions42
- Margin Shift Copy43
- Erase Copy44
  - Edge Erase44
  - Center Erase44
- Dual Page Copy45
- Pamphlet Copy46
- Job Build Mode47
- 2 Copy Functions48
Custom Settings55
- General Procedure for Custom56
- Settings56
- Total Count57
- Settings57
Job Program Memory58
- Storing a Job Program58
- Executing a Job Program59
- Deleting a Stored Job Program59
Auditing Mode60
- Copying When Auditing Mode Is Enabled60
- 5 Troubleshooting and Maintenance61
Display Messages62
Troubleshooting64
- Paper Feeding Problems66
- Image Quality Problems67
Misfeed Removal68
- Misfeed Removal Guidance68
- Misfeed in the Rspf69
- Misfeed in the Bypass Tray70
- Misfeed in the Machine70
- Misfeed in the Center Tray72
- Misfeed in the Upper Paper Tray72
- Misfeed in the Lower Paper Tray73
- MISFEED in the UPPER EXIT AREA (When a Job Separator Tray Kit or Finisher (AR-FN5A) Is Installed)74
- MISFEED in an OUTPUT TRAY (When a Finisher (AR-FN5A) Is Installed)74
Replacing the Toner Cartridge76
Staple Cartridge Replacement77
- Staple Jam Removal78
Checking the Toner Quantity and Total Count78
Cleaning the Machine79
- Document Glass and Rspf79
- The Bypass Tray Paper Feed Roller79
- 6 Peripheral Devices and Supplies80
Peripheral Devices80
- Finisher (Ar-Fn5A)81
- 500-SHEET PAPER FEED UNIT/ 2 X 500-SHEET PAPER FEED UNIT82
Storage of Supplies83
- Proper Storage83
- 7 Appendix84
Specifications84
Material Safety Data Sheet86
Index94
- Index by Purpose97
- Trademark Acknowledgments98

Related product manuals

Preview: Sharp AR-M256

AR-M257 - Digital Imager B/W Laser

Preview: Sharp AR-M236

Preview: Sharp AR-M237

Sharp AR-M237 IMAGERs

AR M207 - B/W Laser - All-in-One

Preview: Sharp AR-M160

Preview: Sharp AR-M452U

Preview: Sharp AR-M451U