Sharp CD-G10000 - Chapter 3: Mechanism Blocks; Disassembly Precautions

CD-G10000/CP-G10000S
3 – 1
AudioCD-G10000/CP-G10000SService ManualCD-G10000/CP-G10000SMarketE
CHAPTER 3. MECHANISM BLOCKS
[1] Caution on disassembly
Caution on Disassembly
Follow the below-mentioned notes when disassembling the unit and reassembling it, to keep it safe and ensure excellent performance:
1. Take cassette tape and compact disc out of the unit.
2. Be sure to remove the power supply plug from the wall outlet before starting to disassemble the unit.
3. Take off nylon bands or wire holders where they need to be removed when disassembling the unit. After servicing the unit, be sure to rearrange
the leads where they were before disassembling.
1 Top/Side Cabinet 1. Screw .................... (A1) x11
2 Changer Unit/ 1. Screw ...................... (B1) x2
Rear Panel B 2. Hook ........................ (B2) x2
3. Flat Cable ................ (B3) x1
4. Socket ..................... (B4) x1
3 Rear Panel A 1. Screw ...................... (C1) x6
with Fan motor/
Terminal PWB
2. Socket .....................
.....................
(C2) x1
4 Main PWB 1. Screw ...................... (D1) x2
2. Flat Cable ............... (D2) x1
3. Socket ..................... (D3) x4
4. Flat Wire .................. (D4) x1
3. Socket (C3) x1
5. Screw ...................... (D5) x4
5 Front Panel 1. Screw ...................... (E1) x2
2. Flat Wire .................. (E2) x1
3. Hook ........................
........................
(E3) x2
6 Tape Mechanism 1. Open the cassette cover.
2. Screw .......................(F1) x6
3. Flat Cable ................(F2) x1
3. Hook (G3) x5
7 Display PWB 1. Knob ........................ (G1) x1
2. Screw .................... (G2) x10
8 Game Input PWB 1. Screw........................ (H1) x2
9 CD Servo PWB 1. Screw ...................... (J1) x2
2. Flat Cable ............... (J2) x2
3. Socket ..................... (J3) x1
4. Hook ........................ (J4) x1
10 Changer 1. Screw ...................... (K1) x4
Mechanism Unit 2. Changer Chassis .... (K2) x1
11 CD Mechanism 1. Screw ...................... (L1) x4
STEP
REMOVAL PROCEDURE
CD-G10000
(A1)x5
M3x10mm
(A1)x3
M3x10mm
(A1)x3
M3x10mm
Rear Panel A
Top/Side Cabinet
Front Panel
Rear Panel B
(D1)x1
M3x10mm
(B1)x2
M3x10mm
Front Panel
Main PWB
Main PWB
(C2)x1
(B2)x1
(B2)x1
Lug Wire
Changer
Mechanism
Unit
Rear
Panel A
Rear
Panel B
Pull
Pull
(E1)x2
M3x8mm
Main
PWB
(E3)x1
(E3)x1
(D1)x1
M3x10mm
(D5)x4
M3x6mm
(D3)x1
(D4)x1
(D3)x1
(E2)x1
Front Panel
(D3)x2
(D2)x1
(C1)x6
M3x10mm
Fan Motor
(C3)x1
Terminal
PWB
Note 1:
After removing the connector for the optical pickup from the
connector, wrap the conductive aluminium foil around the
front end of the connector so as to protect the optical
pickup from electrostatic damage.
(B3)x1
(B4)x1
CD Servo
PWB
Power PWB
jomi