Sharp GX-CD5100W

GX-CD5100W
3 – 1
CD-ES700/CD-ES77CD-ES700/CD-ES77Service ManualCD-ES700/CD-ES77MarketE
CHAPTER 3.
[1] Caution on disassembly
Caution on Disassembly
Follow the below-mentioned notes when disassembling the unit and reassembling it, to keep it safe and ensure
excellent performance:
1. Take cassette tape and compact disc out of the unit.
2. Be sure to remove the power supply plug from the wall outlet before starting to disassemble the unit.
3. Take off nylon bands or wire holders where they need to be removed when disassembling the unit. After servicing
the unit, be sure to rearrange the leads where they were before disassembling.
Note:
After removing the connector for the optical pickup from the
connector, wrap the conductive aluminium foil around the front end
of the connector so as to protect the optical pickup from electro-
static damage.
M3x12mm
(A1)x4
(A1)x3
M3x10mm
(A1)x1
M3x10mm
M3x30mm
(A1)x1
M3x30mm
(A1)x2
M3x10mm
(A1)x1
Battery Cover
PUSH
PUSH
M3x10mm
(L2)x2
Top Cabinet
Front Cabinet
Rear Cabinet
Figure 1
(B2)x1
Front Cabinet
M3x10mm
(B1)x1
M3x10mm
(B1)x1
Top Cabinet
CD Servo PWB
Figure 2
(B2)x1
(B3)x1
(A3)x1
(C2)x2
(C2)x1
Special
(C1)x1
Main
PWB
Front Cabinet
Headphone
PWB
(C2)x4
(C1)x1
Special
(D1)x1
Special
Figure 3
STEP REMOVAL PROCEDURE FIGURE
1 Rear Cabinet/ 1. Open the battery cover. 1
Front Cabinet with
2. Screw……….……………
(A1) X 12 1
Top Cabinet
3. Socket………………..……
(A3) X 2 3,6
2 Top Cabinet
1. Screw…………..…………
(B1) X 2 2
2. Socket……..………………
(B2) X 2
3. Flat Cable……..…………
(B3) X 1
3MainPWB
1. Screw………………..……
(C1) X 2 3
2. Socket……..………………
(C2) X 8
3,4
3. Flat Cable……..…………
(C3) X 1 4
4. MIC……..…………………
(C4) X 1 4
4 Headphone PWB
1. Screw…….…………..……
(D1) X 1 3
5 Tape Mechanism 1. Open the cassette holder. 4
2. Screw……….……………
(E1) X 5
6 Display PWB
1. Knob……..…………..……
(F1) X 1 5
2. Nut…..………………..……
(F2) X 1
3. Washer..……………..……
(F3) X 1
4. Screw………………...……
(F4) X 10
7PowerKeyPWB
1. Screw…………..…………
(G1) X 2 5
8 Tape 1 Knob PWB
1. Screw……….……………
(H1) X 3 5
9 Tape 2 Knob PWB
1. Screw……….……………
(J1) X 3 5
10 Flash PWB
1. Screw…………..…………
(K1) X 2 6
11 Power PWB
1. Plate…………..…………
(L1) X 1 6
2. Screw…………..…………
(L2) X 9 1,6
3. Socket………………..……
(L3) X 3 6
12 CD Servo PWB
1. Screw…………..…………
(M1) X 2 7
2. Socket……..………………
(M2) X 1
3. Flat Cable……..…………
(M3) X 1
13 CD Mechanism
1. Screw…………..…………
(N1) X 4 7
CHAPTER 3. MECHANISM BLOCKS