34
General I would like to have louder
sound by connecting additional
speakers. For TV models with
digital optical audio output.
1) Use the 3.5mm headphone output and a 3.5mm to phono cable (available
separately) to connect to an amplifi er/surround sound system. Please note this
will deactivate the TV’s built in speakers.
2) Connect a digital optical audio cable from the TV’s digital optical audio output
to your amplifi er/surround systems digital optical audio input.
General Why are some options in the menu
unavailable and greyed out.
Some options are only available in certain sources, i.e. HDMI. They are
unavailable in the other sources where they have no a ect.
General Can I stop my TV automatically
turning o after 4hrs?
Yes, in the ‘Time’ menu settings, scroll down to Auto standby and select OFF.
TV I have tuned in Digital TV but I
am not receiving any or all of the
channels and/or the channels I
receive are breaking up.
1) Check you are in an area that can receive Freeview/Saorview, visit www.freeview.co.uk or
www.saorview.ie
2) Check you are using an aerial that is able to receive a good digital signal. In most cases,
you will need an outdoor digital hi-gain/wideband aerial. In areas that have excellent
digital coverage, you may be able to use a loft type aerial but it is highly likely that you will
also need to connect a booster between the back of the TV and the TV aerial wall socket.
Unfortunately, to receive a good enough digital signal, it is not possible to use a portable/
indoor type aerial.
TV I have re-tuned my television but
when I switch it o it is not storing
the channels.
If the TV does not save the channels when you power it o , it’s likely the channel database
has become corrupt.
1) Turn o the TV.
2) Remove the RF/Aerial cable from the rear of the TV and then turn the TV back on again.
3) Using the remote control, press Menu followed by 8-8-8-8 to enter the initial setup/ rst
time installation menu.
4) Press OK (let the TV run the full tuning process).
5) Once completed, turn o the TV, reconnect the RF/Aerial cable then turn the TV back on
again.
6) Repeat steps 3 & 4.
VCR/DVD
Recorder
I have connected the TV to my VCR
or DVD Recorder via SCART but it is
not recording.
In addition to connecting via SCART, you should connect the aerial cable from the wall
socket to your VCR/DVD Recorder and another aerial cable from the VCR/DVD Recorder to
the TV.
Game Consoles I have connected my Playstation/
Xbox to the TV via HDMI, but I am
not receiving any pictures or sound
on my TV
1) Ensure the TVs’ source is set to HDMI.
2) Check your settings on your Playstation/Xbox are as per the Playstation/Xbox
instruction manual.
Game Consoles I have connected my Playstation/
Xbox to the TV via Component
cables (red, green & blue) but I am
not receiving any sound.
Component cables only provide HD pictures. For the sound you will need to connect the
red & white audio cables on the Playstation/Xbox to the red & white phono inputs (or mini
AV input where tted) on the rear of the TV. Please refer to the ‘Connections’ pages.
System Lock I have changed the password
on the television and now
forgotten it.
There is a master password of 4711, to gain access to the TV menu and reset the
normal password.
USB Mode I have inserted a USB Memory Key,
but the TV does not recognise it.
Ensure the USB Memory Key is formatted to type FAT32.
USB Mode Using a USB portable hard drive /
larger than 32GB.
If you wish to use a portable hard drive larger than 32GB, please note that it must be
formatted to the FAT32 le system in order to operate on this TV. Windows XP/Vista
computers are only capable of formatting up to 32GB, therefore, you will need a software
programme/utility to format larger hard drives.
Please refer to the website, www.umc-uk.co.uk, for more information.
USB Record I cannot change the channel, access
the menu or use the red button.
During time shift you cannot change the channel, access the menu or use the red button.
USB Record When using the USB to record the
picture ‘breaks up’ or experience
loss of sound.
Check the USB memory stick meets the minimum read speed requirements. Standard
de nition channels require a read speed of 20 MB/s (Mega Byte per second) and a write
Speed of 6 MB/s (Mega Byte per second) HD channels require the read speed of 80 MB/s
(Mega Byte per second) and a write speed of 40 MB/s (Mega Byte per second). USB 3.0 sticks
should normally ne used where possible.
FREQUENTLY ASKED QUESTIONS
General Information
Sharp - User Guide - SHA-MAN-0229 - CUF8461-2KS.indd Sec1:34Sharp - User Guide - SHA-MAN-0229 - CUF8461-2KS.indd Sec1:34 04/05/2017 12:58:2404/05/2017 12:58:24
To Next Page
Loading...
