EasyManua.ls Logo

Sharp MD-MS701H - Page 21

Sharp MD-MS701H
52 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
MD-MS701H/MS702H
– 21 –
: ATT Setting Check
: Pit section E-ATT (tracking) setting
: Pit section F-ATT (tracking) setting
: Groove section E-ATT (tracking) setting
: Groove section F-ATT (tracking) setting
: High-reflection A-ATT (focus) setting
: High-reflection B-ATT (focus) setting
: Low-reflection A-ATT (focus) setting
: Low-reflection B-ATT (focus) setting
: TCRS-ATT setting
PLAY
R S L T 2
ATT Setting Check
P E
P F
SKIP UP SKIP DOWN
G E
SKIP UP SKIP DOWN
G F
SKIP UP SKIP DOWN
H A
SKIP UP SKIP DOWN
H B
SKIP UP SKIP DOWN
L A
SKIP UP SKIP DOWN
L B
SKIP UP SKIP DOWN
G C
SKIP UP SKIP DOWN
* When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set.
* In the specific setting display state the setting change digit changes when the [P-MODE] key is pressed.
• 3-digit setting
1st digit (initial value) 2nd digit 3rd digit
P-MODE
P-MODE
P-MODE
* In the specific setting display state the value of selection digit changes in the range of "0h to Fh"
when the [VOL UP/DOWN] key is pressed.
: Continuous playback menu
: Continuous playback (pit section)
: Continuous playback (groove section)
# # # # : Address
: Continuous playback (pit section)
: Continuous playback (groove section)
# # # # : Address
PLAY
T P L A Y
Continuous Playback
S Q # # # #
A P # # # #
: Continuous playback (pit section)
: Continuous playback (groove section)
# # # # : Address
: High reflection pit section B-ATT (focus) setting
: High reflection groovesection B-ATT (focus) setting
 : ATT setting
P-MODE
S Q # # # #
A P # # # #
H B
L B
* When the "STOP" button is pressed in specific menu, the TEST MODE STOP state is set.
* In the start address set state the start address changes as follows when the [DISP] key is pressed.
0 0 5 0
H
(initial value) 0 3 C 0
H

0 7 0 0
H
0 8 A 0 H
A d 0 0 5 0
A d 0 3 C 0
DISP
DISP
A d 0 7 9 0
DISP
DISP
A d 0 8 A 0
* In the start address setting state the start address change digit changes when the [BASS] key is pressed.
1st digit (initial value) 2nd digit 3rd digit
A d 0 0 5 0
A d 0 0 5 0
BASS
BASS
A d 0 0 5 0
BASS
* In the continuous playback state the number of jump lines changes as follows shown
the [BASS] key is pressed.
1 (initial value) 10 400
1 T R
1 0 T R
BASS
BASS
4 0 0 T R
BASS
• Continuous playback from current pickup position
: Continuous playback menu
: Start address setting
DISP
T P L A Y
A d 0 0 5 0
PLAY
S Q # # # #
A P # # # #
• Continuous playback from any address
* In the start address set state the value of selection digit changes in the range of "0h to Fh"
when the [SKIP UP/DOWN" key is pressed.
* In the continuous playback state the state is changed to ATT manual adjustment B-ATT setting state
when the [P-MODE] key is pressed.
* In the continuous playback state, jump ocurs in the specified number external periphery direction.
If the key is held down, jump occurs continuously with 100 ms period.

Table of Contents

Other manuals for Sharp MD-MS701H

Related product manuals