EasyManua.ls Logo

Sharp Microwave Drawer Series

Sharp Microwave Drawer Series
4 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
SPECIAL WARNING
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE this installation manual FOR LOCAL ELECTRICAL INSPECTOR’S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CLEARANCES ANd dImENSIoNS
For SAFETY CONSIDERATIONS do not install drawer in any combustible cabinetry, which is not in accord with the stated
clearances and dimensions on page 2. See Figure 1.
Microwave Drawer
InstallatIon Manual
UNPACkING yoUR mICRoWAvE dRAWER
 Remove all packing
materials from inside
t h e M i c r o w a v e
Drawer. DO NOT
R E M O V E T H E
WAVEGUIDE
COVER, which is
located on the top
of the Microwave
Drawer.
 Remove the feature
sticker, if there is one.
Check the drawer for
any damage, such as
misaligned or bent drawer, damaged drawer seals and sealing
surfaces, broken or loose Microwave Drawer guides and dents
inside the cavity or on the front side of the drawer. If there is
any damage, do not operate the Microwave Drawer and contact
your dealer or a SHARP AUTHORIZED SERVICER.
ImPoRtANt NotES to thE INStALLER
 Read all of the Installation Manual before installing the
Microwave Drawer.
 Remove all packing material before connecting the electrical
supply.
 Observe all governing codes and ordinances.
 Be sure to leave these instructions with the consumer.
ImPoRtANt NotES to thE CoNSUmER
Keep this manual with your Operation Manual for future
reference.
 As when using any microwave oven generating heat, there
are certain safety precautions you should follow. These are
listed in the Operation Manual. Read all and follow carefully.
 Be sure your Microwave Drawer is installed and grounded
properly by a qualied installer or service technician.
ImPoRtANt SAfEty INStRUCtIoNS
If the information in this manual is not followed
exactly, a re or electrical shock may result that could cause
property damage, personal injury or death.
To reduce the risk of tipping, the Microwave
Drawer must be secured by a properly installed Anti-Tip
block.
 This Microwave Drawer must be electrically grounded in
accordance with local codes.
 Make sure the wall coverings and the cabinets around the
Microwave Drawer can withstand the heat generated by the
Microwave Drawer.
Never leave children alone or unattended in
the area where a Microwave Drawer is in use. Never leave the
drawer open when the microwave is unattended.
Stepping, leaning or sitting on the drawer may
result in serious injuries and can also cause damage to the
Microwave Drawer.
 Do not use the Microwave Drawer as a storage space.
This creates a potentially hazardous situation.
 Check that the time-of-day is in the display. If not, touch
Stop/Clear to prevent unintended use.
1
Waveguide
cover
Sealing
surface
Oven
cavity
Sealing
surface
Question and Answer IconNeed help?

Do you have a question about the Sharp Microwave Drawer Series and is the answer not in the manual?

Sharp Microwave Drawer Series Specifications

General IconGeneral
TypeMicrowave Drawer
Capacity1.2 cu. ft.
Control TypeTouch
InstallationBuilt-In
Sensor CookYes
DefrostYes
Keep WarmYes
Child LockYes
Wattage1000 W
Display TypeLED
Interior LightYes
Power Output1000W
Installation TypeBuilt-In
TurntableNo
Voltage120V
Frequency60 Hz
Power1000 Watts
FinishStainless Steel
ColorStainless Steel
Warranty1 year

Summary

Special Warnings and Important Notes

Special Warning for Installation

Installation and service must be performed by a qualified installer.

Important Safety Instructions

Fire and Electrical Shock Warning

Failure to follow instructions may cause fire, shock, property damage, or injury.

Anti-Tip Block Requirement

Secure unit with a properly installed Anti-Tip block to reduce tipping risk.

Electrical Grounding Mandate

Must be electrically grounded in accordance with local codes.

Child Safety Warning

Never leave children unattended near a microwave drawer in use or open.

Drawer Stability Warning

Stepping, leaning, or sitting on drawer causes injury and damage.

Anti-Tip Block and Electrical Outlet

Anti-Tip Block Installation

Install block 14 13/16-inches above floor to prevent tipping and injury.

Grounding Plug and Receptacle

Must be plugged into a properly installed and grounded 3-prong receptacle.

Grounding Instructions

Grounding reduces shock risk by providing an escape wire for short circuits.

Grounding Plug Warning

Improper grounding or extension cord use risks electric shock.

Related product manuals