Sharp MX-5112N

21
Required power supply Supplied from nisher
Dimensions
105 mm (W) × 518 mm (D) × 170 mm (H)
(4-9/64" (W) × 20-25/64" (D) × 6-45/64" (H))
115 mm (W) × 600 mm (D) × 995 mm (H)
(4-39/64" (W) × 24" (D) × 39-13/16" (H))
Weight Approx. 3.5 kg (7.7 lbs.) Approx. 8.5 kg (18.7 lbs.)
Required power supply Supplied from saddle nisher
Dimensions
115 mm (W) × 600 mm (D) × 995 mm (H)
(4-39/64" (W) × 24" (D) × 39-13/16" (H))
122 mm (W) × 604 mm (D) × 248 mm (H)
(4-13/16" (W) × 23-25/32" (D) × 9-49/64" (H))
Weight Approx. 8.5 kg (18.7 lbs.) Approx. 3.5 kg (7.7 lbs.)
Finisher (large stacker)
Name Finisher (MX-FN11)
Paper sizes Depends on feeder specications
Useable paper Paper weight 55 g/m
2
(15 lbs.) to 256 g/m
2
(68 lbs.)
No. of trays 2
Tray capacity (80g/m
2
(21 lbs.))
Upper tray
Non-stapled A3 wide (12" × 18") / A3 (11" × 17") / B4 (8-1/2" × 14") /
A4R (8-1/2" × 11"R) / B5R (7-1/4" × 10-1/2"R) /
A5R (5-1/2" × 8-1/2"R): 650 sheets
A4 (8-1/2" × 11") / B5: 1,550 sheets
Staple function A3 (11" × 17") / B4 (8-1/2" × 14") /
A4R (8-1/2" × 11"R): 50 units or 650 sheets
A4 (8-1/2" × 11") / B5: 100 units or 1,550 sheets
Lower tray
Staple function A3 wide (12" × 18") / A3 (11" × 17") / B4 (8-1/2" × 14") /
A4R (8-1/2" × 11"R) / B5R (7-1/4" × 10-1/2"R): 650 sheets
A5R (5-1/2" × 8-1/2"R): 1,700 sheets
A4 (8-1/2" × 11") / B5: 2,450 sheets
Staple function A3 (11" × 17") / B4 (8-1/2" × 14") /
A4R (8-1/2" × 11"R): 50 units or 650 sheets
A4 (8-1/2" × 11") / B5: 100 units or 1,550 sheets
 Offset output is not available for B5R (7-1/4" × 10-1/2"R) /
A3 wide (12" × 18") / A5R (5-1/2" × 8-1/2"R).
Max. no. of stapled sheets
(90 g/m
2
(24 lbs.))
Max. no. of 50 sheets (A4 (8-1/2" × 11"), B5)
Max. no. of 30 sheets (A3 (11" × 17"), B4 (8-1/2" × 14"), A4R (8-1/2" × 11"R))
Staple position 1 bottom, 1 top, 2 middle
Required power supply Supplied from this machine
Weight Approx. 13 kg (28.6 lbs.)
Dimensions
When output paper tray is stored
440 mm (W) × 650 mm (D) × 205 mm (H)
17-39/64" (W) × 25-19/32" (D) × 8-13/64" (H))
When output paper tray is extended
640 mm (W) × 650 mm (D) × 205 mm (H)
(25-39/64" (W) × 25-19/32" (D) × 8-13/64" (H))
Punch module (for saddle nisher)
Name Punch module for MX-FN18 Punch module for MX-FN10
MX-PNX6A / MX-PNX6B,
MX-PNX6C / MX-PNX6D
MX-PNX5A / MX-PNX5B,
MX-PNX5C / MX-PNX5D
Paper size for punch module A3 (11" × 17") to A4 (7-1/4" × 10-1/2"R)
Holes
MX-PNX6A 2 holes, MX-PNX6B 3 holes,
MX-PNX6C 4 holes,
MX-PNX6D 4 holes (wide)
MX-PNX5A 2 holes, MX-PNX5B 3 holes,
MX-PNX5C 4 holes,
MX-PNX5D 4 holes (wide)
Punch module (for nisher)
Name Punch module for MX-FNX9 Punch module for MX-FN11
MX-PNX1A / MX-PNX1B,
MX-PNX1C / MX-PNX1D
MX-PNX6A / MX-PNX6B,
MX-PNX6C / MX-PNX6D
Paper size for punch module A3 (11" × 17") to B5R (7-1/4" × 10-1/2"R)
Holes
MX-PNX1A 2 holes, MX-PNX1B 3 holes,
MX-PNX1C 4 holes,
MX-PNX1D 4 holes (wide)
MX-PNX6A 2 holes, MX-PNX6B 3 holes,
MX-PNX6C 4 holes,
MX-PNX6D 4 holes (wide)