Sharp MX-M550U - Page 124

MX-M700N SIMULATION 7 – 30
30
30-1
Purpose
Operation test/Check
Function (Purpose)
Used to check the operation of sensors and
detectors in other than the paper feed sec-
tion and the operations of the related cir-
cuits.
Section
—
Operation/Procedure
The sensor and detector operation conditions are displayed.
The active sensors and detectors are highlighted.
30-2
Purpose
Operation test/Check
Function (Purpose)
Used to check the operation of sensors and
detectors in the paper feed section and the
related circuits.
Section
Paper feed
Operation/Procedure
The sensor and detector operation conditions are displayed.
The active sensors and detectors are highlighted.
40
40-1
Purpose
Operation test/Check
Function (Purpose)
Used to check the operation of the manual
feed tray paper size detector and the
related circuit. (The operation of the manual
feed tray paper size detector can be moni-
tored with the LCD display.)
Section
Paper feed
Operation/Procedure
The sensor and detector operation conditions are displayed.
The active sensors and detectors are highlighted.
The paper width size detection level is displayed.
PFD2 ADU paper feed detection 2
PPD Resist roller front paper detection
PSD Drum rear paper detection
POD1 After-fusing transport detection 1
POD2 After-fusing transport detection 2
POD3 Paper full detection
DSW_R Manual feed door open detection
DSW_L Cabinet open detection
DSW_F Front cabinet open detection
DSW_DSK Desk door open detection
TFSD Toner remaining quantity detection (Motor rotation
number count)
THPS2 Transfer belt separation home sensor 2
LPPD LCC paper transport detection
T1PPD Tandem tray 1 paper transport sensor
WEB_END Fusing web end detection
TANSET Tray 1 and 2 insertion
detection
TLUD1 Tray 1 upper limit
sensor
TSPD1 Tray 1 remaining
quantity sensor
TPED1 Tray 1 paper sensor
TLUD2 Tray 2 upper limit
sensor
TSPD2 Tray 2 remaining
quantity sensor
TPED2 Tray 2 paper sensor MPLD1 Manual tray length
detection 1
MPLD2 Manual tray length
detection 2
MTOP1 Manual tray pull-out
detection 1
MTOP2 Manual tray pull-out
detection 2
MPED Manual feed paper
empty detection 2
MPFD1 Detection 1 of paper
pass from manual
paper feed
MPFD2 Detection 2 of
paper pass from
manual paper feed
MPRD1 Manual relay paper
detection 1
MPRD2 Manual relay paper
detection 2
Bypass Tray size: (The manual feed tray detection size is displayed.)
M1PFD Tray 3 transport
detection
M1LUD Tray 3 upper limit
detection
SIMULATION 30-1
SENSOR CHECK..
PFD2 PPD PSD POD1
POD2 POD3 DSW_R DSW_L
DSW_F DSW_DSK TFSD THPS2
LPPD T1PPD WEB_END
M1PED Tray 3 paper empty
detection
M1SS1 Tray 3 rear edge
switch 1
M1SS2 Tray 3 rear edge
switch 2
M1SS3 Tray 3 rear edge
switch 3
M1SS4 Tray 3 rear edge
switch 4
M1SPD Tray 3 paper
remaining quantity
detection
Tray 3 size: (The tray 3 detection size is displayed.)
M2PFD Tray 4 transport
detection
M2LUD Tray 4 upper limit
detection
M2PED Tray 4 paper empty
detection
M2SS1 Tray 4 rear edge
switch 1
M2SS2 Tray 4 rear edge
switch 2
M2SS3 Tray 4 rear edge
switch 3
M2SS4 Tray 4 rear edge
switch 4
M2SPD Tray 4 paper
remaining quantity
detection
Tray 4 size: (The tray 4 detection size is displayed.)
MPLD1 Manual tray length detection 1
MPLD2 Manual tray length detection 2
MTOP1 Manual tray pull-out detection 1
MTOP2 Manual tray pull-out detection 2
BYPASS_WIDTH anual feed guide plate position
BYPASS_AD Manual feed width detection volume output AD value
Bypass Tray width
size
(Manual tray detection size is displayed.) A4/A3, 11 x,
B5/B4, 8.5 x , A4R, B5R, A5R, 5.5x, 7.25x, EXTRA
SIMULATION 30-2
TRAY SENSOR CHECK..
TANSET TLUD1 TSPD1 TPED1 TLUD2 TSPD2 TPED2
MPLD1 MPLD2 MTOP1 MTOP2 MPED MPFD1 MPFD2
MPRD1 MPRD2
(Bypass Tray size: A3)
M1PFD M1LUD M1PED M1SS1 M1SS2 M1SS3 M1SS4
M1SPD
(Tray3 size: A3)
M2PFD M2LUD M2PED M2SS1 M2SS2 M2SS3 M2SS4
M2SPD
(Tray4 size: A3)
SIMULATION 40-1
BYPASS TRAY SENSOR CHECK..
MPLD1 MPLD2 MTOP1 MTOP2
BYPASS_WIDTH: 2100 BYPASS_AD: 600
(Bypass Tray width size: A4/A3)