MX-M700N ADJUSTMENTS 6 – 21
2) Using the numeric keypad, select the number that corresponds
to the mode for which to make adjustments.
3) Press the Start key.
4) Enter the copy adjustment value using the numeric keypad.
Make adjustments by changing the adjustment value for high
revolution mode if the copy magnification is not correct for
microcopies; or the adjustment value for low revolution mode if
the copy magnification is not correct for blowbacks.
5) Press the Start key. This applies the adjustment value.
ADJ 7 Adjusting the image off-center
7-A Adjust the print image off-center
(print engine section)
This adjustment is needed in the following situations:
* The paper feed section has been disassembled.
* The MFP control PWB has been replaced.
* The EEPROM on the MFP control PWB has been replaced.
* The scan control PWB has been replaced.
* The EEPROM on the scan control PWB has been replaced.
* The scanner (reading) section has been disassembled.
* The scanner (reading) unit has been replaced.
* The LSU has been replaced.
* U2 trouble has occurred.
(Print image off-center adjustment)
1) Go through the modes specified in Simulation 50-5.
2) Enter the number that corresponds to the paper feed tray that
needs adjustments. (Choose from numbers 10 to 16.)
3) Press the Start key.
4) Press the Start key.
A self-print pattern image is printed.
Check the off-center of the printed self-print pattern image.
If so, no adjustment is required.
Measure the void area dimensions in the front and rear frame
directions, and make sure that the difference between the two
dimensions is within 0r1.5 mm.
Select 0, and press
[START] key.
Press [START] key, or press
[SYSTEM SETTINGS] key.
50
SIMULATION 48-5
SCAN MOTOR SPEED ADJUSTMENT. INPUT VALUE 0-99, AND
PRESS START.
0.MIR(220)
50
2
SIMULATION 50-5
LEAD EDGE ADJUSTMENT. SELECT 0-20, AND PRESS START.
0.TRAY SELECT 1 1.PRINT START
(ADJUSTMENT DATA)
LEAD EDGE: 2.RRCB 50 20.SIDE2 ADJ. 50
RESIST: 3.T1 50 4.T2 50 5.T3 50 6.T4 50
7.BPT 50 8.LCC 50 9.ADU 50
OFF CENTER: 10.T1 50 11.T2 50 12.T3 50 13.T4 50
14.BPT 50 15.LCC 50 16.ADU 50
(VOID SETTING) 17.LEAD_EDGE(DENA) 50
18.TRAIL_EDGE(DENB) 30 19.FRONT/REAR 30
SIMULATION 50-5
LEAD EDGE ADJUSTMENT. NOW PRINTING.
SIMULATION 50-5
LEAD EDGE ADJUSTMENT. INPUT VALUE 0-99, AND PRESS
START.
2.RRCB
Select other than0-1,and
press [START] key.
Press [SYSTEM SETTINGS] key.
Select 1, and
press [START] key.
Press [START] key.
Press [SYSTEM SETTINGS]
key, or terminate copying.
1
SIMULATION 50-5
LEAD EDGE ADJUSTMENT. SELECT 1-16, AND PRESS START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT 6.LCC
(ABOVE+10: DUPLEX MODE)
Item
Setting
range
Default
0TRAY
SELECT
Paper feed tray
selection
1 – 6 –
1 PRINT
START
Print start (Default) – –
(Lead edge adjustment value)
2 RRCB Resist roller clutch
ON timing
adjustment value
0 – 99 50
SIDE2-ADJ Offset (adjustment)
of the RRCB setting
during rear print.
1 – 99
(Resist adjustment value)
3 TRAY1 Tray 1 adjustment 0 – 99 50
4 TRAY2 Tray 2 adjustment
5 TRAY3 Tray 3 adjustment
6 TRAY4 Tray 4 adjustment
7 BPT Manual feed tray
adjustment
8 LCC Side LCC
adjustment
9 ADU Adjustment when
paper is fed again
from ADU
(Off-center set value) Self print
10 TRAY 1 Tray 1 adjustment – –
11 TRAY 2 Tray 2 adjustment – –
12 TRAY 3 Tray 3 adjustment – –
13 TRAY 4 Tray 4 adjustment – –
14 BPT Manual feed tray
adjustment
––
15 LCC Side LCC
adjustment
––
16 ADU Adjustment when
paper is fed again
from ADU
––
(Void set value)
7 LEAD_EDG
E(DENA)
Lead edge void set
value
0 – 99 35
8TRAIL_ED
GE(DENB)
Rear edge void
adjustment value
9 FRONT/
REAR
Front/Rear void
adjustment value
To Next Page
Loading...
