Sharp MX-M550U

MX-M700N SIMULATION 7 – 36
NOTE: When [P] key is pressed after entering an adjustment value
in this simulation, the adjustment value is set. When
[START] key is pressed, the adjustment value is set and
copying is performed.
To select exposure mode, perform the following procedures.
1) Enter 2 with 10-key.
2) Press [START] key. (The mode is changed to the exposure
mode.)
3) Enter the number corresponding to the exposure level to be
used with 10-key, and press [START] key.
46-9
Purpose
Adjustment
Function (Purpose)
Used to adjust the print density for each
density level (display value) in the copy
mode (binary - Text mode). An optional
print density can be set for each density
level (display value).
Section
—
Operation/Procedure
1) Select the number corresponding to the copy density adjust-
ment level with 10-key. (Select one of 3 - 11.)
2) Press the [START] key.
3) Enter the copy density level with 10-key.
4) Press the [P] or [START] key.
The adjustment value is set.
When [START] key is pressed, copy is performed and the
adjustment value is set simultaneously.
Check the density of the printed copy image.
To select paper (paper feed tray), perform the following procedures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray to be
used with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
NOTE: When [P] key is pressed after entering an adjustment value
in this simulation, the adjustment value is set. When
[START] key is pressed, the adjustment value is set and
copying is performed.
46-10
Purpose
Adjustment
Function (Purpose)
Used to adjust the print density for each
density level (display value) in the copy
mode (binary - Text/Photo mode). An
optional print density can be set for each
density level (display value).
Section
—
Operation/Procedure
1) Select the number corresponding to the copy density adjust-
ment level with 10-key. (Select one of 3 - 11.)
2) Press the [START] key.
3) Enter the copy density level with 10-key.
4) Press the [P] or [START] key.
The adjustment value is set.
When [START] key is pressed, copy is performed and the
adjustment value is set simultaneously.
Check the density of the printed copy image.
To select paper (paper feed tray), perform the following procedures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray to be
used with 10-key.
3 AE 3.0 AE mode
4 CH 3.0 Text mode 3.0
5 MIX 3.0 Text/Photo mode 3.0
6 PHOTO 3.0 Photo mode 3.0
Item
Setting
range
Default
0 TRAY SELECT Paper feed tray
selection
1 COPY START Copy START
(Default)
2 EXP LEVEL Exposure level
selection
3 1.0 Exposure level 1.0 0 - 99 50
4 1.5 Exposure level 1.5
5 2.0 Exposure level 2.0
6 2.5 Exposure level 2.5
7 3.0 Exposure level 3.0
8 3.5 Exposure level 3.5
9 4.0 Exposure level 4.0
10 4.5 Exposure level 4.5
11 5.0 Exposure level 5.0
Normal display NOW COPYING.
ERROR display Door open DOOR OPEN.
Jam JAM
Paper empty PAPER EMPTY.
SIMULATION 46-2
1
EXP. LEVEL SETUP (2). SELECT 0-6, AND PRESS START.
0. TRAY SELECT 1 1. COPY START
2. EXP LEVEL 1
3. AE 3.0 50 4. CH 3.0 50
5. MIX 3.0 50 6. PHOTO 3.0 50
1TRAY1 TRAY1
2TRAY2 TRAY2
3TRAY3 TRAY3
4TRAY4 TRAY4
5 BPT Manual paper feed
6 LCC Side LCC
Item
Setting
range
Default
0 TRAY SELECT Paper feed tray
selection
1 COPY START Copy START (Default)
2 EXP LEVEL Exposure level
selection
3 1.0 Exposure level 1.0 0 - 99 50
4 1.5 Exposure level 1.5
5 2.0 Exposure level 2.0
6 2.5 Exposure level 2.5
7 3.0 Exposure level 3.0
8 3.5 Exposure level 3.5
9 4.0 Exposure level 4.0
10 4.5 Exposure level 4.5
11 5.0 Exposure level 5.0
Normal display NOW COPYING.
ERROR display Door open DOOR OPEN.
Jam JAM
Paper empty PAPER EMPTY.
SIMULATION 46-9
1
EXP. LEVEL SETUP (CHAR.2). SELECT 0-11, AND PRESS START.
0. TRAY SELECT 1 1. COPY START
2. EXP LEVEL 1
3. 1.0 50 4. 1.5 50 5. 2.0 50
6. 2.5 50 7. 3.0 50 8. 3.5 50
9. 4.0 50 10. 4.5 50 11. 5.0 50